Aleksey Reshetov

Dr. Aleksey Reshetov

orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2009 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
YBYan Beygelzimer
Yan Beygelzimer
ARAleksey Reshetov
Aleksey Reshetov
SSS. Synkov
S. Synkov
OPO. Prokof’eva
O. Prokof’eva
RKR. Kulagin
R. Kulagin

15 July 2006 in Solid State Phenomena
Verified
Journal Article
Closed access
PDF file
YBYan Beygelzimer
Yan Beygelzimer
Dmytro OrlovDmytro Orlov
Dmytro Orlov
AKAlexander Korshunov
Alexander Korshunov
SSSergey Synkov
Sergey Synkov
VVViktor Varyukhin
Viktor Varyukhin
IKIrina Korotchenkova
Irina Korotchenkova
During the last decade it has been shown that severe plastic deformation (SPD) is a very effective for obtaining ultra-fine grained (UFG) and nanostructured materials. The basic SPD methods are High Pressure Torsion (HPT) and Equal Channel Angular Extrusion (ECAE). Recently several new methods have been developed: 3D deformation, Accumulative Roll Bonding, Constrained Groove Pressing, Repetitive Corrugation and Straightening, Twist Extrusion (TE), etc. In this paper the twist extrusion method is analyzed in terms of SPD processing and the essential features from the “scientific” and “technological” viewpoint are compared with other SPD techniques. Results for commercial, 99.9 wt.% purity, copper processed by TE are reported to show the effectiveness of the method. UFG structure with an average grain size of ~0.3 μm was produced in Cu billets by TE processing. The mechanical properties in copper billets are near their saturation after two TE passes through a 60º die. Subsequent processing improves homogeneity and eliminates anisotropy. The homogeneity of strength for Cu after TE is lower than after ECAE by route BC, but higher than after ECAE by route C. The homogeneity in ductility characteristics was of almost of inverse character. The comparison of mechanical properties inhomogeneity in Cu after TE and ECAE suggests that alternate processing by ECAE and TE should give the most uniform properties.

30 December 2010 in Materials Science Forum
Verified
Journal Article
Closed access
PDF file
VVViktor Varyukhin
Viktor Varyukhin
YBYan Beygelzimer
Yan Beygelzimer
RKR. Kulagin
R. Kulagin
OPO. Prokof'Eva
O. Prokof'Eva
ARAleksey Reshetov
Aleksey Reshetov
We present a study of the kinematics of Twist Extrusion (TE) and show that the mode of deformation in ТЕ is a simple shear. Unlike in Equal-Channel Angular Pressing (ECAP), there are two main shear layers perpendicular to the specimen axis. TE has a significant commercial potential due to the following physical effects: intensive grain refinement; homogenization and mixing; intensive powder consolidation. Donetsk Institute for Physics and Engineering created a TE Center to showcase the process and educate investors. Our experience with the center has shown that the most prospective directions are producing ultrafine-grained (UFG) alloys for medical and aircraft applications.

1 May 2018 in Materials Science and Engineering: A
Verified
Journal Article
Open access
Evgenia YakushinaEvgenia Yakushina
Evgenia Yakushina
ARAleksey Reshetov
Aleksey Reshetov
ISI. Semenova
I. Semenova
VPV. Polyakova
V. Polyakova
ARA. Rosochowski
A. Rosochowski
Ruslan ValievRuslan Valiev
Ruslan Valiev

1 January 2017 in Computer Methods in Material Science
Verified
Journal Article
Open access
NSNicola Stefani
Nicola Stefani
OBOlga Bylya
Olga Bylya
ARAleksey Reshetov
Aleksey Reshetov
PBPaul Blackwell
Paul Blackwell
Nickel-based superalloys are widely used in the aerospace sector for their mechanical properties, which are directly related to the microstructural and physical properties of these materials. JMAK-type models have been applied to this class of superalloys for the prediction of microstructural evolution phenomena such as recrystallisation. However, these models often lack a clear range of applicability. The majority of the successful applications normally address rather idealised processes (relatively slow forging, simple geometry). However, the real-world production environment generally involves complex strain paths and thermal histories. Thus, there arises the question of whether the JMAK-type models can be applied to such cases. This paper’s research focus is to investigate the applicability of JMAK-type models for such processes. To do this, screw press forging of disks was used to validate the in-built JMAK-type model of Inconel 718® available in DEFORMTM. In particular, the applicability of the model was examined using a comparison between the results from simulation and from metallographic analysis. At first, the appropriateness of the JMAK outputs in describing the observed microstructures was investigated and then quantitative results were evaluated. The model’s outputs were found to be insufficient in describing the observed microstructural states and additional parameters were deemed necessary. The model’s predictions ranged from a broadly good match, for which the model could be calibrated with a proposed new methodology, to a qualitative mismatch that highlights the limits of the model’s applicability.

19 January 2006
Verified
Book Chapter
Closed access
PDF file
DOD. Orlov
D. Orlov
ARAleksey Reshetov
Aleksey Reshetov
ASA. Synkov
A. Synkov
VVV. Varyukhin
V. Varyukhin
DLD. Lotsko
D. Lotsko
SSS. Synkov
S. Synkov