In this paper, the green synthesis of isoeugenol methyl ether (IEME) from eugenol by O-methylation and isomerization is completed using a one-step green process. In the methylation reaction, dimethyl carbonate (DMC) was used as a green chemistry reagent instead of the traditional harmful methylation reagents, in accordance with the current concept of green chemistry. The phase transfer catalyst (PTC) polyethylene glycol 800 (PEG-800) was introduced into the isomerization reaction to break the barrier of difficult contact between solid and liquid phases and drastically reduce the reaction conditions by shortening the reaction time and reducing the alkalinity of the reaction system. The catalytic systems for the one-step green synthesis of IEME were screened, and it was shown that the catalytic system “K2CO3 + PEG-800” was the most effective. The effects of reaction temperature, n(DMC):n(eugenol) ratio, n(PEG-800):n(eugenol) ratio, and n(K2CO3):n(eugenol) ratio on eugenol conversion, IEME yield, and IEME selectivity were investigated. The results showed that the best reaction was achieved at a reaction temperature of 140 °C, a reaction time of 3 h, a DMC drip rate of 0.09 mL/min, and n(eugenol):n(DMC):n(K2CO3):n(PEG-800) = 1:3:0.09:0.08. As a result of the conversion of 93.1% of eugenol to IEME, a yield of 86.1% IEME as well as 91.6% IEME selectivity were obtained.
A KF/γ-Al2O3 solid base catalyst was prepared by wet impregnation and applied to the synthesis of eugenol ethyl ether (EEE) from eugenol and diethyl carbonate. By measuring the yield of eugenol ethyl ether, we investigated the effects of the catalyst active component, impregnation temperature, KF impregnation concentration, impregnation time, and calcination temperature on catalyst performance. The results showed that the KF/γ-Al2O3 catalyst can adequately facilitate the conversion of eugenol to EEE. The characterizations of the catalysts were examined by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM). The characterizations of EEE were examined by nuclear magnetic resonance spectrometry (H1-NMR), gas chromatography–mass spectrometer (GC-MS) and Fourier-transform infrared spectroscopy (FT-IR). It was found that the KF/Al2O3 catalyst (impregnation temperature 60 °C, KF impregnation concentration 40%, impregnation time 8 h, and calcination temperature 450 °C) showed the best effect. The yield of EEE remained 51.2% after recycling the supported catalyst three times.
Biomass frequently constrains its widespread application due to its low economic efficiency. In this project, a new approach of biomass application was explored to reduce bio-syngas production cost. A model for the bio-syngas production from biomass gasification and bio-syngas purification (Selexol and water scrubbing) were studied. Based on the simulation results, we assessed the feasibility and viability of the project. Preliminary results showed that the bio-syngas production cost with Selexol (2.15 $/Nm3) is even higher than biomass used in power generation systems (equal to 1.58–2.21 $/Nm3). However, water scrubber was used as bio-syngas purification, the capital investment cost and bio-syngas production cost (1.34 $/Nm3) was significantly reduced. A sensitivity analysis was conducted on the bio-syngas price, which could be further reduced by various factors: biomass price, carbon taxes, and carbon credits. We assumed that bio-syngas was applied to natural gas pipeline, our analysis showed that the application of bio-syngas (2–10% content) to natural gas had little impact on natural gas properties: combustion value and price. The technology of water scrubber makes the applications of biomass-based fuels competitive.
13 February 2024 in Biomass Conversion and Biorefinery