Joanna Warycha

Dr. Joanna Warycha

Wrocław University of Science and Technology, Wrocław, Dolnośląskie, Poland
orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2014 in Ceramics International
Verified
Journal Article
Closed access
GPGrzegorz Paściak
Grzegorz Paściak
WMWitold Mielcarek
Witold Mielcarek
KPKrystyna Prociów
Krystyna Prociów
JWJoanna Warycha
Joanna Warycha

17 October 2022 in Polymers
Verified
Journal Article
Open access
PDF file
PZPaweł Zielonka
Paweł Zielonka
Szymon DudaSzymon Duda
Szymon Duda
Grzegorz LesiukGrzegorz Lesiuk
Grzegorz Lesiuk
WBWojciech Błażejewski
Wojciech Błażejewski
MWMagdalena Wiśniewska
Magdalena Wiśniewska
BBBartosz Babiarczuk
Bartosz Babiarczuk
Fire resistance is a major issue concerning composite materials for safe operation in many industrial sectors. The design process needs to meet safety requirements for buildings and vehicles, where the use of composites has increased. There are several solutions to increasing the flame resistance of polymeric materials, based on either chemical modification or physical additions to the material’s composition. Generally, the used flame retardants affect mechanical properties either in a positive or negative way. The presented research shows the influence of the mixed-mode behavior of epoxy resin. Fracture toughness tests on epoxy resin samples were carried out, to investigate the changes resulting from different inorganic filler contents of aluminum trihydroxide (ATH). Three-point bending and asymmetric four-point bending tests, with different loading modes, were performed, to check the fracture behavior in a complex state of loading. The results showed that the fracture toughness of mode I and mode II was reduced by over 50%, compared to neat resin. The experimental outcomes were compared with theoretical predictions, demonstrating that the crack initiation angle for higher values of KI/KII factor had a reasonable correlation with the MTS prediction. On the other hand, for small values of the factor KI/KII, the results of the crack initiation angle had significant divergences. Additionally, based on scanning electron microscopy images, the fracturing of the samples was presented.

1 September 2013 in Ceramics International
Verified
Journal Article
Closed access
WMWitold Mielcarek
Witold Mielcarek
AGAdam Gubański
Adam Gubański
GPGrzegorz Paściak
Grzegorz Paściak
KPKrystyna Prociów
Krystyna Prociów
JWJoanna Warycha
Joanna Warycha
JWJerzy M. Wrobel
Jerzy M. Wrobel

9 September 2021 in International Journal of Fracture
Verified
Journal Article
Open access
PDF file
MDMonika Duda
Monika Duda
Dariusz RozumekDariusz Rozumek
Dariusz Rozumek
Grzegorz LesiukGrzegorz Lesiuk
Grzegorz Lesiuk
Michał Jan SmolnickiMichał Jan Smolnicki
Michał Jan Smolnicki
BBBartosz Babiarczuk
Bartosz Babiarczuk
JWJoanna Warycha
Joanna Warycha
The paper contains the results of an experimental investigation of fatigue crack development under mixed-mode I + II and I + III in heat-treated 42CrMo4 steel. Tests were performed on heat-treated compact tension shear specimens and rectangular cross-section specimens for mixed-mode I + III. Mixed-mode I + II tests were conducted for 30 and 60° loading angle, while the test for I + III mixed-mode was conducted for 30 and 45°. Additionally, the paper presents fracture analysis results of fatigue crack path development.

21 February 2024 in Alexandria Engineering Journal
Verified
Journal Article
Open access
WBWojciech Błażejewski
Wojciech Błażejewski
MBMichał Barcikowski
Michał Barcikowski
MSMichał Stosiak
Michał Stosiak
JWJoanna Warycha
Joanna Warycha
PSPaweł Stabla
Paweł Stabla
KPKarolina Paczkowska
Karolina Paczkowska

1 December 2015 in IEEE Transactions on Dielectrics and Electrical Insulation
Verified
Journal Article
Closed access
BMBolesław Mazurek
Bolesław Mazurek
WMWitold Mielcarek
Witold Mielcarek
JWJoanna Warycha
Joanna Warycha
KPKrystyna Prociow
Krystyna Prociow
JCJacek Chmielowiec
Jacek Chmielowiec
EPEwa Popko
Ewa Popko
The influence of graphene deposition on emission spectrum of Cu electrodes was investigated. In this order the two types of samples were prepared: one from a pure copper plate, and one from a copper plate covered with graphene. The graphene has been obtained using Chemical Vapor Deposition (CVD) method. The analysis of I=f(E) and Fowler-Nordheim (F-N) characteristics showed that a graphene layer uniformly deposited on a cathode, parallel to its surface creates a shielding for microprotrusions which causes a decrease of electric field and, consequently, the β coefficient. This occurs regardless whether the sample surface had been etched before graphene deposition or not. The F-N characteristics showed that the cathode emission mechanism is changing with the increase of field intensity. Initially, the emission current is blocked by a surface adsorption layer. With further increase of the field intensity, up the Eth value, a typical F- N mechanism occurs until microdischarges appear. As a result of microdischarges, under the influence of cathode potential, electrons are emitted, which bombard the anode. This current has a form of pulses repeated approximately every 4.5 ns until plasma is created on anode, what is in fact equivalent to a breakdown.