Sławomir Poskrobko

Prof. Dr. Sławomir Poskrobko


Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 January 2022 in Energies
Verified
Journal Article
Open access
PDF file
DKDanuta Król
Danuta Król
Przemysław MotylPrzemysław Motyl
Przemysław Motyl
SPSławomir Poskrobko
Sławomir Poskrobko
The selection of appropriate heat-resistant materials which are at the same time resistant to atmospheres rich in chlorine and its compounds is one of the most important current construction problems in steel boiler elements when using biomass fuels of agricultural origin. In the research presented here, an area was identified in the furnace of a 10 kW boiler where there was a potential risk of chlorine corrosion. This zone was determined based on numerical analysis of the combustion process; it is the zone with the highest temperatures and where the gas atmosphere conducive to the formation of chlorine corrosion centers. Subsequently, tests were carried out in the process environment of the combustion chamber of a 10 kW boiler (the fuel was barley straw) by placing samples of eight construction materials in a numerically-designated zone. These included samples of steel (coal boiler St41K, heat-resistant H25T and H24JS, and heat-resistant valve 50H21G9N4) as well as intermetallic materials based on phases (FeAl, Fe3Al, NiAl, and Ni3Al). The samples remained in the atmosphere of the boiler furnace for 1152 h at a temperature of 750–900 °C. After this time, the surfaces of the samples were subjected to SEM microscopy and scanning analysis. The results showed that the St41K boiler steel was not suitable for operation under the assumed conditions, and that a thick layer of complex corrosion products was visible on its surface. The least amount of corrosion damage was observed for the samples of 50H21G9N4 steel and intermetallic materials.

31 October 2022 in Energies
Verified
Journal Article
Open access
PDF file
DKDanuta Król
Danuta Król
Przemysław MotylPrzemysław Motyl
Przemysław Motyl
SPSławomir Poskrobko
Sławomir Poskrobko
The main sources of environmental pollution with heavy (ecotoxic) metals include industry, including utility and municipal power engineering, but also waste incineration plants. Fuel shortages and their constantly growing prices raise concerns that energy will be commonly obtained from waste outside of installations intended for this purpose (i.e., outside waste incineration plants). The greatest concern stems from the risk of burning waste in low-power boilers—domestic boilers. Waste incineration plants and utility power plants are equipped with flue gas cleaning installations (FGD), but low-power boilers are not. The exhaust gases are directly introduced into the atmosphere, which results in the introduction into the air of, inter alia, toxic heavy metals. Therefore, it is necessary to conduct activities aimed at retaining ecotoxic metals in the solid–slag residue. The paper presents the results of laboratory tests of the emission capacity of Cd, Cu, Zn bound in various chemical forms—nitrates (V), chlorides and sulphates (VI). The tests were carried out at 1073 K, 1173 K and 1273 K. It was found that the emissivity of metals increased with increasing temperature. This is innovative as there are no reports of experiments with pure forms of metal salts. The advantage of this type of research is the lack of influence from other factors, apart from temperature, on metal emissions. To check the possibility of reducing metal emissions, additives (bauxite, dolomite, V2O5) immobilized in a solid residue were tested. The mechanism of action of each of the additives to limit the mobility of metals was different. The use of V2O5 for this purpose is new. The additives kept the metals solid in the residue, but their effect was different for each of the metals. The effectiveness of the tested additives was checked in the same temperature conditions, burning waste such as: rubber, sewage sludge and SRF fuel from waste. The effect of the additives depended on the type of waste, type of metal and the furnace temperature. If the additive effectively retained metals, then their amounts in the ashes were higher by several to several dozen percent in relation to the amount in the ashes remaining after waste incineration without additives. The results of the experiment with waste are open to research on the influence of other factors (except temperature) on the emissivity of Cd, Cu, Zn and the possibility of its reduction. The next step will be to verify the effects of laboratory tests in real conditions.

9 November 2020 in Energies
Verified
Journal Article
Open access
PDF file
Przemysław MotylPrzemysław Motyl
Przemysław Motyl
DKDanuta Król
Danuta Król
SPSławomir Poskrobko
Sławomir Poskrobko
MJMarek Juszczak
Marek Juszczak
The paper presents the results of numerical and experimental studies aimed at developing a new design of a 10 kW low-emission heating boiler fired with wood pellets. The boiler is to meet stringent requirements in terms of efficiency (η > 90%) and emissions per 10% O2: CO < 500 mg/Nm3, NOx ≤ 200 mg/Nm3, and dust ≤ 20 mg/Nm3; these emission restrictions are as prescribed in the applicable ECODESIGN Directive in the European Union countries. An innovative aspect of the boiler structure (not yet present in domestic boilers) is the circular flow of exhaust gases around the centrally placed combustion chamber. The use of such a solution ensures high-efficiency, low-emission combustion and meeting the requirements of ECODESIGN. The results of the numerical calculations were verified and confirmed experimentally, obtaining average emission values of the limited gases CO = 91 mg/Nm3, and NOx = 197 mg/Nm3. The temperature measured in the furnace is 450–500 °C and in the flue it was 157–197 °C. The determined boiler efficiency was 92%. Numerical calculations were made with the use of an advanced CFD (Computational Fluid Dynamics) workshop in the form of the Ansys programming and a computing environment with the dominant participation of the Fluent module. It was shown that the results obtained in both experiments are sufficiently convergent.

1 December 2016 in Energy
Verified
Journal Article
Closed access
DKDanuta Król
Danuta Król
SPSławomir Poskrobko
Sławomir Poskrobko

20 January 2012 in Energy & Fuels
Verified
Journal Article
Closed access
SPSławomir Poskrobko
Sławomir Poskrobko
DKDanuta Król
Danuta Król
JŁJan Łach
Jan Łach

27 March 2017 in Energy & Fuels
Verified
Journal Article
Closed access
DKDanuta Król
Danuta Król
SPSławomir Poskrobko
Sławomir Poskrobko