Byung-Su Kim

Prof. Dr. Byung-Su Kim

Korea Institute of Geoscience & Mineral Resources

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 April 2015 in Minerals
Verified
Journal Article
Open access
PDF file
DSDoyun Shin
Doyun Shin
Ji-Woong KimJi-Woong Kim
Ji-Woong Kim
BKByung-Su Kim
Byung-Su Kim
JJJinki Jeong
Jinki Jeong
Jae-chun LeeJae-chun Lee
Jae-chun Lee
In the present study, the feasibility to use phosphate solubilizing bacteria (PSB) to develop a biological leaching process of rare earth elements (REE) from monazite-bearing ore was determined. To predict the REE leaching capacity of bacteria, the phosphate solubilizing abilities of 10 species of PSB were determined by halo zone formation on Reyes minimal agar media supplemented with bromo cresol green together with a phosphate solubilization test in Reyes minimal liquid media as the screening studies. Calcium phosphate was used as a model mineral phosphate. Among the test PSB strains, Pseudomonas fluorescens, P. putida, P. rhizosphaerae, Mesorhizobium ciceri, Bacillus megaterium, and Acetobacter aceti formed halo zones, with the zone of A. aceti being the widest. In the phosphate solubilization test in liquid media, Azospirillum lipoferum, P. rhizosphaerae, B. megaterium, and A. aceti caused the leaching of 6.4%, 6.9%, 7.5%, and 32.5% of calcium, respectively. When PSB were used to leach REE from monazite-bearing ore, ~5.7 mg/L of cerium (0.13% of leaching efficiency) and ~2.8 mg/L of lanthanum (0.11%) were leached by A. aceti, and Azospirillum brasilense, A. lipoferum, P. rhizosphaerae and M. ciceri leached 0.5–1 mg/L of both cerium and lanthanum (0.005%–0.01%), as measured by concentrations in the leaching liquor. These results indicate that determination of halo zone formation was found as a useful method to select high-capacity bacteria in REE leaching. However, as the leaching efficiency determined in our experiments was low, even in the presence of A. aceti, further studies are now underway to enhance leaching efficiency by selecting other microorganisms based on halo zone formation.

1 January 2004 in JOURNAL OF CHEMICAL ENGINEERING OF JAPAN
Verified
Journal Article
Closed access
JYJae-Min Yoo
Jae-Min Yoo
Jae-chun LeeJae-chun Lee
Jae-chun Lee
BKByung-Su Kim
Byung-Su Kim
HLHi Sun Lee
Hi Sun Lee
JJJin-Ki Jeong
Jin-Ki Jeong

9 November 2020 in Metals
Verified
Journal Article
Open access
PDF file
JCJi-Hyuk Choi
Ji-Hyuk Choi
HCHankwon Chang
Hankwon Chang
TRTaegong Ryu
Taegong Ryu
CNChul-Woo Nam
Chul-Woo Nam
BKByung-Su Kim
Byung-Su Kim
The aluminothermic process is used for producing ferrotitanium alloy (FeTi) from an ilmenite concentrate. In this study, based on thermodynamic calculations and experiments, we investigated the effects of adding varying amounts of exothermal agent (NaClO3), slag-forming agent (CaO), and reducing agent (Al) on the recovery ratio of Ti in the aluminothermic process. The thermodynamic calculations suggested that the exothermal agent plays a crucial role in producing the FeTi alloy from the ilmenite concentrate and the maximum Ti grade in the FeTi alloy was approximately 30 wt %. Experimentally, it was verified that the FeTi alloy obtained under the optimum mixing conditions contained 30.2–30.8 wt % Ti, 1.1–1.3 wt % Si, 9.5–11.2 wt % Al, and 56.9–58.0 wt % Fe, along with trace impurities and small amounts of gases such as oxygen (0.35–0.66 wt %) and nitrogen (0.01–0.02 wt %). At the optimum mixing conditions, the recovery ratio of Ti into the obtained FeTi alloy phase was 60.6–68.9%. These results matched closely with the thermodynamic calculations. Therefore, the thermodynamic calculations performed herein are expected to significantly contribute toward the development of new processes and improvement in conventional processes for producing various ferroalloys including the FeTi alloy through the aluminothermic process.

1 January 2004 in MATERIALS TRANSACTIONS
Verified
Journal Article
Closed access
Jae-chun LeeJae-chun Lee
Jae-chun Lee
JJJinki Jeong
Jinki Jeong
BKByung-Su Kim
Byung-Su Kim
MKMin Seuk Kim
Min Seuk Kim
MKMikio Kobayashi
Mikio Kobayashi

1 January 2008 in MATERIALS TRANSACTIONS
Verified
Journal Article
Open access
BKByung-Su Kim
Byung-Su Kim
HLHoo-In Lee
Hoo-In Lee
JPJin-Tae Park
Jin-Tae Park
JSJeong-Soo Sohn
Jeong-Soo Sohn
Jae-chun LeeJae-chun Lee
Jae-chun Lee

4 July 2022 in Geosystem Engineering
Verified
Journal Article
Closed access
BKByung-Su Kim
Byung-Su Kim
TRTae-Gong Ryu
Tae-Gong Ryu
JCJi-Hyuk Choi
Ji-Hyuk Choi
TPTae Jun Park
Tae Jun Park
HCHankwon Chang
Hankwon Chang
KRKimin Roh
Kimin Roh
A vanadium electrolyte for energy storage is generally prepared by dissolving vanadium pentoxide (V2O5) in sulfuric acid using oxalic acid ((COOH)2) as a reducing agent. However, there is a disadvantage that the dissolution rate in the sulfuric acid solution of V2O5 is very slow. In this study, a new process for producing vanadium dioxide (VO2), which has the faster dissolution rate than V2O5 in sulfuric acid solution, was developed. Vanadium dioxide (VO2) could be used in the production of a vanadium electrolyte for energy storage. The process developed in the study has the advantages of being economical and simple as compared to the existing process for producing VO2 from V2O5 using hydrogen or carbon monoxide as a reducing agent.