This article focuses on studying the effects of muscle and fat percentages on the exergy behavior of the human body under several environmental conditions. The main objective is to relate the thermal comfort indicators with exergy rates, resulting in a Second Law perspective to evaluate thermal environment. A phenomenological model is proposed of the human body with four layers: core, muscle, fat and skin. The choice of a simplified model is justified by the facility to variate the amount of mass in each tissue without knowing how it spreads around the body. After validated, the model was subjected to a set of environmental conditions and body compositions. The results obtained indicate that the area normalization (Watts per square meter) may be used as a safe generalization for the exergy transfer to environment. Moreover, the destroyed exergy itself is sufficient to evaluate the thermal sensation when the model is submitted to environmental temperatures lower than that considered for the thermal neutrality condition (and, in this text, the thermal comfort) . Nevertheless, for environments with temperatures higher than the calculated for the thermal neutrality, the combination of destroyed exergy and the rate of exergy transferred to the environment should be used to properly evaluate thermal comfort.

Phase separation based centrifugal forces is effective, and thus widely explored by the process industry. In an inline swirl separator, a core of the light phase is formed in the center of the device and captured further downstream. Given the inlet conditions, this gas core created varies in shape and size. To predict the separation behavior and control the process in an optimal way, the gas core diameter should be measured with the minimum possible intrusiveness. Process tomography techniques such as electrical resistance tomography (ERT) allows us to measure the gas core diameter in a fast and non-intrusive way. Due to the soft-field nature and ill-posed problem in solving the inverse problem, especially in the area of low spatial resolution, the reconstructed images often overestimate the diameter of the object under consideration leading to unreliable measurements. To use ERT measurements as an input for the controller, the estimated diameters should be corrected based on secondary measurements, e.g., optical techniques such as high-speed cameras. In this context, image processing and image analysis techniques were adapted to compare the diameter calculated by an ERT system and a fast camera. In this paper, a correction method is introduced to correct the diameter obtained by ERT based on static measurements. The proposed method reduced the ERT error of dynamic measurements of the gas core size from over 300% to below 20%, making it a reliable sensing technique for controlled separation processes.

The performance of multiphase flow processes is often determined by the distribution of phases inside the equipment. However, controllers in the field are typically implemented based on flow variables, which are simpler to measure, but indirectly connected to performance (e.g., pressure). Tomography has been used in the study of the distribution of phases of multiphase flows for decades, but only recently, the temporal resolution of the technique was sufficient for real-time reconstructions of the flow. Due to the strong connection between the performance and distribution of phases, it is expected that the introduction of tomography to the real-time control of multiphase flows will lead to substantial improvements in the system performance in relation to the current controllers in the field. This paper uses a gas–liquid inline swirl separator to analyze the possibilities and limitations of tomography-based real-time control of multiphase flow processes. Experiments were performed in the separator using a wire-mesh sensor (WMS) and a high-speed camera to show that multiphase flows have two components in their dynamics: one intrinsic to its nonlinear physics, occurring independent of external process disturbances, and one due to process disturbances (e.g., changes in the flow rates of the installation). Moreover, it is shown that the intrinsic dynamics propagate from upstream to inside the separator and can be used in predictive and feedforward control strategies. In addition to the WMS experiments, a proportional–integral feedback controller based on electrical resistance tomography (ERT) was implemented in the separator, with successful results in relation to the control of the distribution of phases and impact on the performance of the process: the capture of gas was increased from 76% to 93% of the total gas with the tomography-based controller. The results obtained with the inline swirl separator are extended in the perspective of the tomography-based control of quasi-1D multiphase flows.

Electrical resistance tomography (ERT) has been used in the literature to monitor the gas–liquid separation. However, the image reconstruction algorithms used in the studies take a considerable amount of time to generate the tomograms, which is far above the time scales of the flow inside the inline separator and, as a consequence, the technique is not fast enough to capture all the relevant dynamics of the process, vital for control applications. This article proposes a new strategy based on the physics behind the measurement and simple logics to monitor the separation with a high temporal resolution by minimizing both the amount of data and the calculations required to reconstruct one frame of the flow. To demonstrate its potential, the electronics of an ERT system are used together with a high-speed camera to measure the flow inside an inline swirl separator. For the 16-electrode system used in this study, only 12 measurements are required to reconstruct the whole flow distribution with the proposed algorithm, 10× less than the minimum number of measurements of ERT (120). In terms of computational effort, the technique was shown to be 1000× faster than solving the inverse problem non-iteratively via the Gauss–Newton approach, one of the computationally cheapest techniques available. Therefore, this novel algorithm has the potential to achieve measurement speeds in the order of 10⁴ times the ERT speed in the context of inline swirl separation, pointing to flow measurements at around 10kHz while keeping the average estimation error below 6 mm in the worst-case scenario.

When swirl is added to gas-liquid upward vertical pipe flows (e.g. inside an inline swirl separator), the classical flow patterns are modified by the centrifugal forces which act pushing the gas towards the center of the pipe and the liquid towards the wall. If the swirl is strong enough, this leads to the formation of a gas column in the center of the pipe, which can be either stable or intermittent. It was observed experimentally that the behavior of the gas column is strongly dependent on the dynamics of the gas-liquid flow upstream of the addition of swirl. In this video, a high speed camera was used to record the gas-liquid flow upstream and downstream of a swirl-generating element for different flow rates of liquid and gas, covering multiple non-swirling (upstream) and swirling flow patterns (downstream). The video: (i) shows the different swirling gas-liquid flow patterns and their dynamic behavior; (ii) analyzes the connection between the dynamics of the swirl patterns and the gas-liquid patterns upstream of the swirl element, via synchronized recordings of the two locations.

Electrical Resistance Tomography (ERT) has been used in the literature to monitor the gas-liquid separation. However, the image reconstruction algorithms used in the studies take a considerable amount of time to generate the tomograms, which is far above the time scales of the flow inside the inline separator and, as a consequence, the technique is not fast enough to capture all the rele-vant dynamics of the process, vital for control applications. This article proposes a new strategy based on the physics behind the measurement and simple logics to monitor the separation with a high temporal resolution by minimizing both the amount of data and the calculations required to reconstruct one frame of the flow. To demonstrate its potential, the electronics of an ERT system are used together with a high-speed camera to measure the flow inside an inline swirl separator. For the 16-electrode system used in this study, only 12 measurements are required to reconstruct the whole flow distribution with the proposed algorithm, 10x less than the minimum number of measurements of ERT (120). In terms of computational effort, the technique was shown to be 1000x faster than solving the inverse problem non-iteratively via the Gauss-Newton approach, one of the computationally cheapest techniques available. Therefore, this novel algorithm has the potential to achieve measurement speeds in the order of 104 times the ERT speed in the context of inline swirl separation, pointing to flow measurements at around 10kHz while keeping the aver-age estimation error below 6 mm in the worst case scenario.