The horizontal rotor wave energy converter is a newly designed wave energy converter. While the mooring system plays a vital role in keeping the device floating stably, the selection of the mooring angle has immediate effects on the device’s floating stability and energy generation efficiency. Given the properties of wave energy along the coast in Shandong Province, this study combines wave statistics gathered from field measurements of a certain area in the Bohai Sea with hydrological data obtained in a field test in the same sea area and adopts Stokes’ fifth-order wave theory to theoretically design and simulate the mooring system for the new type of power generating device. With the help of AQWA software, data on the dynamics of the device at various angles are obtained to construct models and carry out regular wave experiments according to the most appropriate mooring angles to show the validity of the selected mooring angles. The consistency of the results between the experiment and simulation confirms that under the same working conditions of regular waves, as the mooring angle increases, the roll angle decreases first and then increases, the pitch angle barely varies, and the yaw angle decreases first and then increases. The adoption of this simulation method and the gathered experimental data help to provide theoretical and practical bases for choosing the mooring method for the engineering prototype and obtaining a reliable supply of power.
As traditional energy sources are increasingly depleting, ocean energy has become an emergent potential clean energy source. Wave energy, as an important part of ocean-derived energy, has been studied and utilized by coastal countries worldwide, which have developed various wave energy converters. In this paper, a new wave energy converter is designed, and water movement in fluid channels is analyzed. The results are, then, used to generate a mathematical model that simulates water movement. Based on this approach, the water movement state is analyzed, and a formula for calculating the natural frequency of water movement in the power generator is derived. The formula shows that the characteristic length of the water movement in the proposed generator and the backboard tilt angle at the exit point of the fluid channel are two design-related variables that can be used to alter the natural frequency; a regular wave experiment is conducted based on the fluid model, which is designed based on the natural frequency formula, to verify the changes in model torque and speed as well as whether the model can operate under normal wave conditions. This study lays a theoretical foundation for the design of further experiments and engineering prototypes to verify the validity of mathematical models by way of experimental analysis.
The mooring system not only plays a vital role in keeping wave energy generators floating stably, but also affects the success of engineering design. Combining wave force theory and the hydrological data obtained from the field measurements of a certain sea area in the Bohai Sea, the Stokes second-order wave theory was adopted to design the mooring system of a new type of power-generating device. At the same time, the study uses the Aqwa software to gather the dynamic data of a power-generating device in a real test, and then makes models and carries out regular wave tests so as to verify the viability of the mooring system and the stability of the whole power-generating device. All of this work will provide a theoretical basis for the manufacture of an engineering prototype and its reliable supply of power.
The development and utilization of wave energy is inseparable from the wave energy converter, and its stability is an important condition for operation. Heave is the biggest factor affecting the stable power generation of wave energy converters. The key method to solve this problem is to install a suitable heave plate. Therefore, the design of the heave plate is particularly important. Based on a new type of horizontal rotor wave energy converter, this paper proposes three different shapes of heave plate design schemes and completes the calculation and modeling of the engineering prototype. First, the three types of heave plate devices were numerically simulated using hydrodynamic calculation software to compare their stable performances and verify the feasibility of the scheme. Subsequently, an experimental model was made according to the parameters of the engineering prototype, and a tank experiment was carried out under the same working conditions to further study the influence of the heave plate installation distance on the stability of the wave energy generator. The results showed that when the distance was between 10 mm and 20 mm, the average amplitude change was large, and when the distance was between 20 mm and 30 mm, the average amplitude change was small. Therefore, the installation distance should be between 20 mm and 30 mm. In the case of the same heave plate area and installation distance, the average amplitude of the chamfered heave plate device was smaller than the other two types, indicating that its stability was better. The optimization of the shape and installation distance of the heave plate proposed in this study has obvious effects on improving the stability of the device and provides a reference for the design of the wave energy converter device.
Nowadays antiretroviral therapy is widely used to cut down the viral burden and cut off a few infection sources in clinical medicine for Human Immunodeficiency Virus (HIV) infected patients, and a lot of evidence have shown that a massive coverage with antiretroviral therapy has already acquired a series of contributions and successes to save life and popularize preventive knowledge. Based on the HIV dynamic model, this paper designs a feedback controller to adjust the concentration values of CD4+T cell, CD8+T cell and viral load in HIV dynamic model to a healthy condition asymptotically. The HIV dynamic model is expressed in the form of a polynomial system and then the control law, as the appropriate drug dosage usually applied in the medical therapy, is designed to suppress the reproduction of the HIV virus and improve the production rate of healthy cell in vivo, simultaneously. According to the polynomial Lyapunov theory and sum of squares (SOS) technique, the conditions for the controller synthesis are proposed. The simulation experimental results can be testified the availability of the proposed method.