Carbon nanofibers with high surface area have become promising electrode materials for supercapacitors because of their importance in increasing energy density. In this study, a high free volume polymer, 6FDA-DAM:DABA (6FDD) was blended with polybenzimidazole (PBI) in different ratios to obtain different compositions of PBI/6FDD immiscible polymer blends. Freestanding nanofiber mats were obtained via electrospinning using blend precursors dissolved in N,N-dimethylacetamide (DMAc). Subsequently, carbonization, followed by CO2 activation at 1000 °C was applied to convert the fiber mats into porous carbon nanofibers (CNFs). The addition of 6FDD shows significant effects on the microstructure and enhancement of the surface area of the CNFs. The obtained CNFs show specific surface area as high as 3010 m2 g−1 with pore sizes comparable to those of the electrolyte ions (PYR14TFSI). This provides good electrolyte accessibility to the pore of the carbon materials resulting in enhanced energy density compared to the CNFs obtained from pure PBI. Electrodes derived from PBI:6FDD (70 : 30) exhibited outstanding supercapacitor performance in coin cells with a specific capacitance of 142 F g−1 at the scan rate of 10 mV s−1 and energy density of 67.5 W h kg−1 at 1 A g−1 (58 W h kg−1 at 10 A g−1) thus demonstrating promising electrochemical performance for high performance energy storage system.
Lanthanum hydroxide nanorods were employed as both a template and catalyst for carbon synthesis by chemical vapor deposition. The resulting carbon possesses hollow nanorod shapes with graphitic walls. The hollow carbon nanorods were interconnected at some junctions forming a mazelike network, and the broken ends of the tubular carbon provide accessibility to the inner surface of the carbon, resulting in a surface area of 771 m2/g. The hollow carbon was tested as an electrode material for supercapacitors. A specific capacitance of 128 F/g, an energy density of 55 Wh/kg, and a power density of 1700 W/kg at 1 A/g were obtained using the ionic liquid, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, as the electrolyte.
A new europium-based complex, K[Eu(hfa)4] with hfa = hexafluoroacetylacetonate is synthesized and its structure confirmed via X-ray crystallography. The structure unravels an anionic octa-coordinate complex, K[Eu(hfa)4], as opposed to the neutral hexacoordinate complex Eu(hfa)3 routinely/ubiquitously presumed to be the case in the literature. The complex displayed pH-dependent, “on–off” emission changes in solution and exhibited a pKa of 6.13 ± 0.06 in ethylene glycol. In solution, the sensor complex exhibited drastic variation in emission intensity corresponding to changes in the concentration of CO2 gas purged. Based on multiple purge cycles of N2 and CO2, the emission intensity changes can be correlated to the concentration of CO2 in the solution. The sensor’s ability to quantify the CO2 presence is based on emission variations of the 5D0 → 7F2 line in the Eu(III) complex at 618 nm. The sensor exhibits a linear response to CO2 concentrations in the range of 0–25% (0–8.50 mM or 0–189.95 mmHg). Based on calibration data, the limit of detection (LOD) is determined to be 0.57% (0.19 mM or 4.33 mmHg) in solution. The I100/I0 ratio is determined to be 80.29 ± 3.79. The percent change in intensity from purging N2 to 100% CO2 is 7911.16%. Over the course of seven cycles of purging different concentrations of CO2, there is essentially no deviation in the emission intensity of the sensor in solution, indicating stability and reversibility. In addition to the analytical characterization of the sensor, the mechanism of CO2 sensing is investigated using cyclic voltammetry, IR, and Raman spectroscopy. These data indicate the reduction of europium(III) to europium(II) in an alkaline medium and suggest changes in the hfa ligand chemistry (association/dissociation and protonation) due to CO2 purging. The potential use of the sensor complex for real-life applications is herein evaluated via a well-known fermentation reaction. The CO2 generated during yeast’s anaerobic respiration in sucrose media is quantified using the sensor complex and a calibrated, commercial CO2 probe; both exhibit similar CO2 concentration values, validating the calibration curve and the viability of the complex as a bona fide sensor. Based on the data collected, a highly stable, brightly red-emissive Eu(III) complex with the ability to differentiate concentrations of CO2 in solution is hereby developed and characterized with benefits for various CO2 sensing applications.
8 January 2020 in ECS Journal of Solid State Science and Technology
An electropolymerizable zinc porphyrin carrying eight entities of peripheral bithiophene, 4 was newly designed and synthesized. In this design, the bithiophene entities were separated by a biphenyl spacer to minimize ground state interactions perturbing porphyrin π-electronic structure. By multi-cyclic voltammetry, thin-films of 4 were formed on transparent FTO electrode and were characterized by optical, electrochemical and STM measurements. Further, the ability of zinc porphyrin in 4 to axially coordinate phenyl imidazole functionalized fullerene, C60Im both in solution and on the film interface was performed and characterized. Fluorescence quenching of zinc porphyrin both in solution and in the film was observed upon binding of C60Im. Femtosecond transient absorption studies revealed excited state charge separation for the dyad in solution wherein the measured rate of charge separation, kCS and charge recombination, kCR were found to be 2 × 1010 s−1 and 1.2 × 109 s−1, respectively. In contrast, transient absorption studies performed on the dyad in the film were suggestive of energy transfer with minimal contributions from electron transfer. The present study brings out the importance of modulating photochemical reactivity of donor-acceptor dyad in film as compared to that in solution.