Magnetite is an essential iron-bearing mineral. The primary method of magnetite ore beneficiation involves successive steps of crushing, grinding, and magnetic separation. Reverse cationic flotation is used at the final stage to remove silicate and aluminosilicate impurities from the magnetite concentrate and reduce silica content to 1–3%, depending on metallurgical processing route (electrometallurgy, direct iron reduction). In view of the stringent demands of the magnetite concentrate grade, before flotation, the ore is currently routinely ground down to a particle size below 35 µm, and magnetite particles are ground to a size below 10 µm. This significantly reduces the efficiency of flotation and increases iron loss in the tailings due to the hydraulic report in froth being up to 15–25%. Combined microflotation (CMF) looks to be a promising method of increasing fine-particle flotation efficiency, as it uses relatively small amounts of microbubbles alongside conventional coarse bubbles. Microbubbles act as flotation carriers, collecting gangue particles on their surface, which then coarse bubbles float. The purpose of this study is to explore the effectiveness of CMF for processing a model mixture that contained magnetite particles smaller than 10 µm and glass beads (Ballotini) below 37 µm in size when the initial iron content in the mixture was 63.76%. Commercial reagent Lilaflot 821M was used as both collector and frother. The flotation procedure, which included the introduction of 15 g/t of the collector before the start of flotation, and the addition of 5 g/t of the collector in combination with a microbubble dose of 0.018 m3/t 6 min after starting flotation, ensured an increase in the concentrate grade to 67.63% Fe and iron recovery of 91.16%.
Magnetite ores are among the most important sources of iron, which is in high demand in the global economy. Metallurgical properties of the magnetite concentrate significantly depend on impurities of silicon- and aluminum-bearing minerals. These impurities have to be separated from ore by magnetic separation and flotation techniques. Reverse column flotation is one of the methods applied for reducing the content of impurities in magnetite concentrate. This method allows recovering impurities from ore in the froth product (flotation tailings). However, the efficiency of this method significantly decreases with the decrease in particle size. As previously demonstrated, the effectiveness of fine particle column flotation can be increased if, before feeding the pulp into a column, fine bubbles are introduced into the pulp and the pulp is then passed through a tubular reactor. The major purpose of this study was to define the effectiveness of the reverse column flotation performance of ultrafine magnetite from the mixture with fine glass beads (ballotini) when, before the pulp is fed into the flotation column, it is mixed with fine air-in-water dispersion, and the mixture is then passed through a tubular flotation reactor (TFR). The obtained experimental findings allowed the definition of the optimal conditions of the mixture treatment in TFR that ensured high concentrate grade and iron recovery for the initial iron content in the mixture of 63.76%. These conditions were defined as follows: treatment time of the mixture in the TFR—7.5 s; average flow shear rate inside the TFR—1000 s−1; volume dosage of fine bubbles per solid mass unit—0.032 or 0.21 mL/g. At the fine bubble dosage of 0.032 mL/g, the iron recovery and the concentrate grade were, respectively, 88.1% and 68.3% Fe, and at the dosage of 0.21 mL/g, the iron recovery reached 89.4% for the concentrate grade of 68.7% Fe.
25 December 2025 in Journal of Chemistry and Technologies
The growth of industrial and agricultural production inevitably leads to an increase in freshwater deficiency, and this is indeed observed on all continents of our planet. The only way to overcome this challenging problem is to develop effective methods for purifying circulating water from dispersed and soluble substances, including heavy metal ions and water-soluble components petroleum products (Toluene, Benzene, Phenol, and similar ones.) It is generally recognised that the simplest, most accessible, and cheapest way to purify water from soluble contaminants is the use of ultrafine clay sorbents. Studies on the process of separating clay suspensions have been conducted using samples of clays mined from deposits in Ukraine. The samples were treated with anionic flocculants. The effectiveness of flocculants, their optimal dose, and the optimal medium shear rate in the flocculator were defined using the device UltraFloc-Tester “UFT-TFS-029”.It was found that, depending on the properties of the clay, the treatment of the clay suspension (3 g/l) for 6 seconds in a flocculator at a medium shear rate of 1000–1500 s-1 followed by subsequent separation in a flow-through horizontal micro-settler for 55 seconds, allowed to achieve the residual suspension concentration around 0.18–0.42 g/l. Additionally, it has been found that Magnafloc 5250 can be regarded as the most effective and commonly used all-purpose flocculant for the studied clay suspensions.