Marina Fedorischeva

Dr. Marina Fedorischeva

Institute of Strength Physics and Materials Science, SB RAS
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 August 2023 in Metals
Verified
Journal Article
Open access
PDF file
TDTamara I. Dorofeeva
Tamara I. Dorofeeva
Marina FedorischevaMarina Fedorischeva
Marina Fedorischeva
TGTatiana A. Gubaidulina
Tatiana A. Gubaidulina
OSOleg V. Sergeev
Oleg V. Sergeev
ASAlfred R. Sungatulin
Alfred R. Sungatulin
SVSergeev P. Victor
Sergeev P. Victor
In this work, the corrosion resistance of AISI 321 stainless steel is increased through. the two-stage implantation of oxygen ions and of both aluminum and boron ions together. During ion implantation, a modified layer with a thickness of about 200 nm is formed, which affects the properties of material. The increase in corrosion resistance is confirmed by prolonged acid corrosion tests at pH 3.5 and by accelerated electrochemical tests using a potentiostat. The corrosion rate of the implanted sample is 0.708 μA/cm2, in contrast to the non-implanted sample (1.26 μA/cm2). The modified surface layer is examined using X-ray photoelectron spectroscopy (XPS), secondary-ion mass spectrometry (SIMS), and transmission electron microscopy (TEM). Aluminum and boron are implanted to a depth of more than 250 nm. It is found that the modified surface of the stainless steel substrate contains oxides of implanted ions (Al2O3) and oxides of substrate ions (Cr2O3 and NiCr2O4).

28 January 2022 in Metals
Verified
Journal Article
Open access
PDF file
TDTamara Dorofeeva
Tamara Dorofeeva
TGTatiana Gubaidulina
Tatiana Gubaidulina
VSVictor Sergeev
Victor Sergeev
Marina FedorischevaMarina Fedorischeva
Marina Fedorischeva
This work studies single-layer (Al-Si-N) and multi-layer (Al-Si-N-O/Al-Si-O) coatings deposited by magnetron sputtering on stainless steel specimens (AISI 321), which can be used under aggressive conditions. The multi-layer coating consists of six alternating layers of Al-Si-N-O and Al-Si-O with a thickness of 0.9 µm and 0.2 µm, respectively. The structural-phase state and the chemical composition of the coatings were studied by transmission and scanning electron microscopy and XPS analysis. It was revealed that single-layer coatings are nanocrystalline and contain AlN and α-Si3N4 phases. Multi-layer coatings (Al-Si-N-O/Al-Si-O) are amorphous in each of the layers. The corrosion properties of substrate and coated specimens were investigated using a potentiostat in the 3.5 mg/l sea salt solution. It was found that corrosion resistance of stainless steel specimens with multi-layer coating is substantially (tenfold) higher compared with substrates and the specimens with single-layer coating.

1 May 2017 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
VSV P Sergeev
V P Sergeev
MKM P Kalashnikov
M P Kalashnikov
IBI A Bozhko
I A Bozhko
ERE V Rybalko
E V Rybalko
OSO V Sergeev
O V Sergeev
Marina FedorischevaMarina Fedorischeva
Marina Fedorischeva
The purpose of this research is design of a magnetron deposition technology for quartz glasses of optically transparent nanocomposite protective coatings based on Al-Si-N with preliminary modification of the substrate surface by a high-energy Ni+ ion beam. The coating improves the mechanical properties and resistance of the glass to the impact of highspeed iron microparticles. The structural-phase state and elemental composition of the coatings and the surface layer of the substrate are investigated by electron microscopy, electron-probe analysis, and secondary ion mass spectrometry.

1 January 2016 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
IBIrina Bozhko
Irina Bozhko
EREvgeniya Rybalko
Evgeniya Rybalko
APAnastasiya Pershukova
Anastasiya Pershukova
Marina FedorischevaMarina Fedorischeva
Marina Fedorischeva
YKYurii Khristenko
Yurii Khristenko
VSVictor Sergeev
Victor Sergeev
The paper presents the results of investigations of the structural and phase conditions, mechanical and optical properties of Al-Si-N system coating obtained by magnetron sputtering. The thickness of this coating ranges from 3 to 19 µm and is sprayed on silica glass using magnetron sputtering technique. The formation of nanoscale AlN single phase with HCP crystal system and the crystal grain size of up to 20 nm is discovered using the X-ray diffraction method. The texture of [002] orientation is observed in the structure of Al-Si-N-based coatings. These coatings are characterized by high values of microhardness and coefficient of restitution. The transmission spectrum of the coatings are produced within the range of 190-1100 nm. Al-Si-N-based coatings are characterized by a high degree of transparency (≈ 80%) within the visible light spectrum and complete opaqueness in the ultraviolet region. The refractive index and the thickness of Al-Si-N system coating are determined using the transmission spectrum and refractive index. The refractive index of Al-Si-N-coated glass samples is determined using the transmission spectrum the value of which increases with the increase in the coating thickness.

1 December 2022 in Russian Physics Journal
Verified
Journal Article
Closed access
PDF file
TDT. I. Dorofeeva
T. I. Dorofeeva
Marina FedorischevaMarina Fedorischeva
Marina Fedorischeva
TGT. A. Gubaidulina
T. A. Gubaidulina
VSV. P. Sergeev
V. P. Sergeev
MKM. P. Kalashnikov
M. P. Kalashnikov
AVA. V. Voronov
A. V. Voronov

27 November 2020 in Metals
Verified
Journal Article
Open access
PDF file
Marina FedorischevaMarina Fedorischeva
Marina Fedorischeva
MKMark Kalashnikov
Mark Kalashnikov
IBIrina Bozhko
Irina Bozhko
OPOlga Perevalova
Olga Perevalova
VSVictor Sergeev
Victor Sergeev
To improve the strength properties, adhesion, and the thermal cycling resistance of ceramic coatings, the titanium alloy surface was modified with copper ions under different processing times. It is found that at the maximum processing time, the thickness of the alloyed layer reaches 12 μm. It is shown that the modified layer has a multiphase structure in addition to the main α and β–titanium phases with the intermetallic compounds of the Ti-Cu system. The parameters of the fine structure of the material are investigated by the X-ray diffraction analysis. It has been found that when the surface of the titanium alloy is modified, depletion occurs in the main alloying elements, such as aluminum and vanadium, the crystal lattice parameter increases, the root-mean-square (rms) displacements of the atoms decrease, and the macrostresses of compression arise. A multilevel micro- and nanoporous nanocrystalline structure occurs, which leads to an increase in the adhesion and the thermal cyclic resistance of the ceramic coating based on Si-Al-N.