Seung-Woo Lee

Prof. Seung-Woo Lee

Kyung Hee University
orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2017 in Optical Engineering
Verified
Journal Article
Closed access
PDF file
SKSeung-Ryeol Kim
Seung-Ryeol Kim
SLSeung-Hyuck Lee
Seung-Hyuck Lee
DJDong-Hwan Jeon
Dong-Hwan Jeon
JKJeong-Sik Kim
Jeong-Sik Kim
Seung-Woo LeeSeung-Woo Lee
Seung-Woo Lee
Viewing high luminance displays under low light conditions causes unbearable glare. On the other hand, viewing low luminance displays under bright light conditions reduces visibility. We investigate the comfortable display luminance range for several different conditions of ambient illuminance through a psychophysical experiment, which involved 30 subjects. The obtained upper (lower) limits of the comfortable zone were 516 (113), 574 (116), 612 (130), 664 (154), 737 (177), 790 (204), and 836 (246)  cd/m2, for ambient illuminances of 50, 100, 200, 500, 1000, 2000, and 5000 lx, respectively.

17 November 2020 in IEEE Access
Verified
Journal Article
Open access
JKJeong-Sik Kim
Jeong-Sik Kim
Seung-Woo LeeSeung-Woo Lee
Seung-Woo Lee
In this paper, a new low-power technology based on gaze tracking, called peripheral dimming, is proposed for organic light-emitting diode (OLED) displays. The goal of the proposed method is to save power without degrading the perceptual image quality. In the proposed method, the peripheral vision area on the screen is gradually darkened depending on the distance from the gaze point. In this work, quantitative conditions for preventing degradation of the perceived image quality are studied through a psychophysical experiment by using three video clips. We suggest a lightness reduction ratio (LRR) that determines the amount of reduced luminance per viewing angle based on the lightness. Four conditions of the LRR from 0.1 to 1.0%/degree are applied to each clip. The experiment is designed based on a two-alternative forced choice: a test clip with the proposed method is compared to the original one, and subjects are forced to choose the brighter clip between the two clips shown in random order. In this way, the threshold of the LRR from which people begin to notice a difference between the test and original clips is obtained. The experimental results demonstrate that the proposed method saves the power of OLED displays up to 34.4% while keeping the image quality high in terms of both subjective and objective quality (the mean structural similarity index is higher than 0.94). Therefore, the proposed method will help to enable low-power operation of OLED displays used for head-mounted display devices while maintaining the quality of experience.

27 April 2020 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
JKJongbin Kim
Jongbin Kim
HCHoon-Ju Chung
Hoon-Ju Chung
Seung-Woo LeeSeung-Woo Lee
Seung-Woo Lee

23 April 2015 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
Seung-Woo LeeSeung-Woo Lee
Seung-Woo Lee
JKJongbin Kim
Jongbin Kim
SYSeong Ho Yoon
Seong Ho Yoon
KKKyeong-Ah Kim
Kyeong-Ah Kim
SYSung-Min Yoon
Sung-Min Yoon
KCKyoung-Ik Cho
Kyoung-Ik Cho
A new pixel architecture and driving scheme for a low-power liquid crystal display (LCD) with a low refresh-rate is proposed. The proposed pixel architecture comprises two oxide thin-film transistors (Ox-TFTs), two ferroelectric memory TFTs (Fe-MTFTs), and two capacitors. Both TFTs have the same indium gallium zinc oxide film as an active layer. The Fe-MTFT exhibits a hysteresis property owing to the ferroelectric gate insulator that enables it to operate as a memory. A prototype LCD with 6 × 5 pixels is fabricated in this letter. The fieldeffect mobility of Ox-TFTs is 11 cm 2 V -1 s -1 . The memory window of Fe-MTFT is 5 V with a gate-voltage sweep from -20 to 20 V. After programming the Fe-MTFTs, the fabricated LCD successfully operates at a 0.5-Hz refresh-rate.

29 October 2019 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
JKJongbin Kim
Jongbin Kim
HCHoon-Ju Chung
Hoon-Ju Chung
Seung-Woo LeeSeung-Woo Lee
Seung-Woo Lee
We propose a new memory-in-pixel (MIP) circuit using low temperature poly-silicon and oxide (LTPO) thin film transistors (TFTs) to achieve the high reliability as well as low power consumption. The proposed pixel circuit can greatly reduce the frame frequency due to extremely low leakage current of oxide TFTs. Moreover, the driving TFTs of the circuit can be stable under continuous stress for a long period of time because low temperature poly-silicon TFTs show high reliability. The pixel is driven directly by applying black or white voltage so that a flicker can be minimized. Fabricated circuit successfully verifies the circuit performance under the frame frequency of 1/60 Hz and the polarity inversion frequency of 0.5 Hz. Therefore, we expect that our proposed MIP circuit can provide flicker-free liquid crystal displays featuring low power consumption as well as high reliability.

22 February 2018 in Optical Engineering
Verified
Journal Article
Open access
PDF file
MKMinkoo Kim
Minkoo Kim
DJDong-Hwan Jeon
Dong-Hwan Jeon
JKJeong-Sik Kim
Jeong-Sik Kim
BYByung-Chang Yu
Byung-Chang Yu
YPYungKyung Park
YungKyung Park
Seung-Woo LeeSeung-Woo Lee
Seung-Woo Lee
Recently, the use of displays in everyday life has increased several fold in almost every environment. In particular, mobile displays used in cell phones and tablet PCs can be used in any situation because of their portability and are widely used indoors as well as outdoors. When people look at these displays, they want to have consistent visibility at every location. However, most users are still dissatisfied because of insufficient display brightness in bright environments and too much brightness in dark environments. Visibility is worsened when a display is viewed under high illumination conditions without increasing the display luminance. On the other hand, viewing the display in low-light conditions without controlling the brightness causes uncomfortable glare.1 2. 3. 4. – 5 To maintain the visibility of the displays in all conditions, it is necessary to adjust the brightness of the displays according to the ambient light.