Wet chemical analysis techniques for four elements (M = As, Pb, Sb, and Sn) in Ag – M binary alloys were investigated with emphasis on the choice of solvent acid and the characteristic wavelength used in the ICP-AES (Inductively-Coupled Plasma Atomic Emission Spectrometer) analysis. The elements are representative tramp elements in ferrous scrap. The activity of these elements needs to be increased to remove them efficiently during the molten scrap refining process. The activity of these elements in the molten scrap (molten iron alloy) is usually measured by a chemical equilibration technique with molten Ag. Therefore, performing an accurate and reliable chemical analysis of these elements in the molten iron alloy and the molten Ag alloy is important. Preliminary tests using conventional acids (hydrochloric acid, nitric acid) resulted in unreliable results. In the present study, the proper choice of acids as solvents was investigated for each element M in the Ag-M alloys. Several synthesized Ag-M alloys of known compositions were analyzed using two ICP-AES systems independently, for cross-checking. As and Pb in Ag alloys could be successfully dissolved in the nitric acid-based solution. On the other hand, Sb and Sn in Ag alloys did not dissolve in the nitric acid-based solution completely, leaving some precipitates. It was found that the addition of hydrofluoric acid could resolve this problem. In addition to this, the effect of the mass of the Ag-M alloy and wavelength selection during ICP-AES analysis on the accuracy and the reproducibility were investigated. An optimized procedure for the wet chemical analysis of these elements in Ag-M alloys is reported.
In the steelmaking process, MgAl2O4 spinel inclusions diminish steel qualities and cause nozzle clogging based on the high melting point and low deformation of MgAl2O4. Typically, MgAl2O4 spinel inclusions are generated from Al2O3 inclusions with increasing Mg0 content, meaning ladle treatment does not represent an equilibrium state. However, complex reactions simultaneously occur between molten steel, slag, inclusions, refractory, and alloying elements during ladle treatment. Therefore, it is necessary to develop a kinetic model to predict compositional changes in molten steel, slag, and the inclusions during ladle treatment. Such a kinetic model must be able to simulate the generation of MgAl2O4 spinel inclusions from Al2O3 to control such inclusions. Additionally, MgAl2O4 spinel inclusions can evolve into MgO-rich inclusions with gradually increasing MgO content in Mg-Al-based inclusions. In this study, we developed an enhanced kinetic model based on a coupled reaction model with the compositional changes in Mg Albased inclusions. We also investigated the influence of the CaO/SiO2 ratio in slag on the generation of spinel inclusions under industrial conditions for a 210-ton steel sample.
7 August 2018 in Metallurgical and Materials Transactions B
At present, copper smelting slag is not effectively recycled and is wasted. Copper smelting slag contains FexO at more than 40 mass%. For the utilization of copper slag as a Fe resource, it is necessary to separate the Cu in the slag. For copper recycling from slag, FeS-based matte can be introduced to use sulfurization to concentrate Cu from the slag into the sulfide and finally recover the copper. In a previous paper, a kinetic model was developed to simulate the coupled reactions between the multicomponent slag and FeS-based matte by using previously reported thermodynamic data. Building on this work, we carried out equilibrium experiments to supplement the thermodynamic data used in the previously developed model. An empirical formula for the Cu2O activity coefficient of Cu2O-FeOX-CaO-MgO-SiO2-Al2O3 system slag was obtained. In addition, the effect of alumina content in the slag on the Cu2O activity coefficient in the slag was investigated. The model was also supplemented to account for MgO solubility. By the developed model and the industrial conditions, we investigated the effect of slag composition on the behavior of Cu between matte and Cu2O-FeOX-CaO-MgO-SiO2-Al2O3 system slag for the copper loss.