Maksim Grigorev

Prof. Maksim Grigorev

South Ural State University, 454080, Chelyabinsk, Lenin Prospect, 76, Russia
orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2014 in Russian Electrical Engineering
Verified
Journal Article
Closed access
PDF file
Maksim GrigorevMaksim Grigorev
Maksim Grigorev
Power circuit arrangements of independently excited reactive electric drives are presented. It is shown that the number of switches is determined by the number of phases and lies in the range from 2f to 4f. It has been ascertained by regression analysis that the unit price of semiconductor converters at minor current values does not depend on current and is determined by the cost of the microprocessor control system. At currents >100 A, the price-current relation is nearly linear and the rejection of three-phase power circuits of semiconductor converters in favor of multiphase power circuits does not therefore increase power supply weight and size. Thus, the more complex configuration of power circuit arrangements (increased number of phases) for processing plants with an installed capacity of more than 200 kW can improve the weight and size of the electromechanical converter while maintaining the size of the semiconductor converter.

15 June 2009 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
PDF file
UUU. S. Usinin
U. S. Usinin
Maksim GrigorevMaksim Grigorev
Maksim Grigorev
KVK. M. Vinogradov
K. M. Vinogradov
AGA. N. Gorojankin
A. N. Gorojankin
SGS. P. Gladyshev
S. P. Gladyshev
The electric drive with the synchronous electrical machine of independent excitation differs by high specific parameters, adaptability to manufacture, simplicity of a design, and reliability. These properties of the electric drive allow using it in heavy conditions of operation. In particular, it can be recommended to use in electrical vehicles. The electric motor for this electric drive can be executed with two separate stator windings. Therefore, there are additional benefits connected to an opportunity of change of geometry of an iron stator stamp of the given type motor. In this report, the principle of operation of the electric drive with control system is considered. The different variants of a stator design of the electrical machine are discussed. The stator design allows improve of the mass and weight parameters of the electric machine. For the offered stator designs, the comparison of specific parameters (relationship of the nominal torque to load current) is carried out. The received results of analysis are discussed.

5 November 2020 in Machines
Verified
Journal Article
Open access
PDF file
VOVsevolod Ostrouhov
Vsevolod Ostrouhov
DSDmitry Sychev
Dmitry Sychev
Maksim GrigorevMaksim Grigorev
Maksim Grigorev
This article deals with installations with complex and nonstandard executive instrument movement. Having analyzed the technical implementation and operational features of cold-rolling pipe mills, the research team formulated the problem of synthesizing electric drives of auxiliary mechanisms. It is shown that the conditions for choosing a mechanical converter are associated with the oscillation of the processes of the electric drive system. The finite element method and the gradient descent method are used for structural analysis of solids and electromagnetic calculations. The data of the specific cost of semiconductor converters were analyzed using a linear least-squares regression technique. The advantages of a synchronous reluctance motor of independent excitation for the electric drives of auxiliary mechanisms are given and substantiated. The optimization of the geometrical parameters of the electromechanical converter was carried out according to the maximum developed electromagnetic torque. Modern semiconductor technology in the design of special-purpose electric drives leads to a revision of the principles for determining the optimal number of phases and the structure of the motor power supply. The rationale for the use of multilevel frequency converters is given. Taking into account an in-depth preliminary analysis and an integrated approach, these tasks were successfully completed, which was confirmed experimentally at the implementation of the developed system.

24 September 2013 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
PDF file
UUUriy Usinin
Uriy Usinin
SGSergey Gladyshev
Sergey Gladyshev
Maksim GrigorevMaksim Grigorev
Maksim Grigorev
ASAlexander Shishkov
Alexander Shishkov
ABAnton Bychkov
Anton Bychkov
EBEvgeny Belousov
Evgeny Belousov
A traction electric drive is offered for an industrial tractor. The drive contains the generator, the controlled rectifier, the independent inverters, and two onboard motors. The important feature of the offered electric drive is application of synchronous reactive machines of independent excitation as the generator and traction motors. These electric machines have the following technical features: the generator and motor design is brushless; and simple, the rotor has high mechanical rigidity that raises reliability at high speeds and overloads. There are no windings on the rotor; the motor is designed for ease of manufacture (by expert estimations its price is lower than the squirrel cage induction motor on the order of 15-20 %). The machines have increased efficiency a result of a “cold” rotor design; the motors have high torque overloads capacity (up to 4-6 times the values of nominal torque). The windings of the motor and the generator are single-layered with full step capability of current and voltage. The motor control is transistors based. The range of the torque regulation is 1:10 resulting in constant power for the drive. The stator circuits are supplied from individual current sources via transistor single-phase autonomous inverters. The intermediate direct current link design of the three-wire circuit allows the use of half the number of transistors in the autonomous inverters. In the generator, working and excitation are divided to simplify the power circuits of the converter. The control system of the drive is similar to electric drives of a direct current machine and can have several operating modes. This electric drive is not only a good traction drive, but also has possible application for other mechanisms where high load duty cycles are required for operation, because the simplicity of a design. It is brushless and has a high operational and overload torques capability.

12 April 2010 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
PDF file
SGSergey P. Gladyshev
Sergey P. Gladyshev
YUYuriy Usinin
Yuriy Usinin
Maksim GrigorevMaksim Grigorev
Maksim Grigorev
KVKonstantin Vinogradov
Konstantin Vinogradov
ASA. Shishkov
A. Shishkov
ABA. Bychkov
A. Bychkov
The field regulated reluctance machine is perspective for automotive transport electric drives. In this machine, the switching of a stator current is done in function of a rotor position. The massive salient rotor of the electric machine does not contain windings. The stator is fulfilled in the body and iron of serial ac induction motor. The stator winding sections, which conductors lay above between rotor poles intervals, serve as a excitation winding, and others sections, which conductors lay above rotor poles, the role of a armature winding. In most cases, the optimal winding current waveform is distinct from the sine waveform. For a case of use separate current sources for each phase, the ideal is rectangular waveform. At the rotation of the motor, the each stator section winding pass from a zone of “excitation” to a zone of “armature”. The stator has finite number of phases. At switching stator currents, the part of a phase, in which there is a switching of an armature current, is in a zone of excitation, and another - in a zone of an armature. It causes additional losses in the rotor, because the rotor is fabricated massive (not laminated). For calculation of the losses first of all it is necessary to determine the factors, which influence on their value, and then, to estimate a degree of influence of each of them on value of switching losses. As such factors are taken: the form of the stator core, the form of a current in phase windings, and the number of stator winding phases. The calculation of losses is executed by the method of winding functions. The experimental data are received on a breadboard model of the 20 kW drive.

9 November 2024 in Sensors
Verified
Journal Article
Open access
PDF file
ZZZihan Zhang
Zihan Zhang
QGQihui Guo
Qihui Guo
Maksim GrigorevMaksim Grigorev
Maksim Grigorev
IKIvan Kholodilin
Ivan Kholodilin
Due to the high cost of robots, the algorithm testing cost for physical robots is high, and the construction of motion control programs is complex, with low operation fault tolerance. To address this issue, this paper proposes a low-cost, cross-platform SCARA robot digital-twin simulation system based on the concept of digital twins. This method establishes a 5D architecture based on the characteristics of different platforms, classifies data and integrates functions, and designs a data-processing layer for motion trajectory calculation and data storage for a virtual-reality robot. To address the complexity of data interaction under different cross-platform communication forms, an editable, modular, cross-platform communication system is constructed, and various control commands are encapsulated into simple programming statements for easy invocation. Experimental results showed that, based on modular communication control, users can accurately control data communication and synchronous motion between virtual and physical models using simple command statements, reducing the development cost of control algorithms. Meanwhile, the virtual-robot simulation system, as a data mapping of the real experimental platform, accurately simulated the physical robot’s operating state and spatial environment. The robot algorithms tested using the virtual simulation system can be successfully applied to real robot platforms, accurately reproducing the operating results of the virtual system.