Marc Martí

Mr. Marc Martí

Universitat Rovira i Virgili, Av. Països Catalans 26, Tarragona, Spain
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 July 2023 in Biosensors
Verified
Journal Article
Open access
PDF file
ALAntonio Lazaro
Antonio Lazaro
RVRamon Villarino
Ramon Villarino
Marc MartíMarc Martí
Marc Martí
NCNicolau Canyellas
Nicolau Canyellas
Beatriz Prieto-SimónBeatriz Prieto-Simón
Beatriz Prieto-Simón
DGDavid Girbau
David Girbau
This article reviews the recent advances in the field of batteryless near-field communication (NFC) sensors for chemical sensing and biosensing. The commercial availability of low-cost commercial NFC integrated circuits (ICs) and their massive integration in smartphones, used as readers and cloud interfaces, have aroused great interest in new batteryless NFC sensors. The fact that coil antennas are not importantly affected by the body compared with other wireless sensors based on far-field communications makes this technology suitable for future wearable point-of-care testing (PoCT) devices. This review first compares energy harvesting based on NFC to other energy-harvesting technologies. Next, some practical recommendations for designing and tuning NFC-based tags are described. Power transfer is key because in most cases, the energy harvested has to be stable for several seconds and not contaminated by undesired signals. For this reason, the effect of the dimensions of the coils and the conductivity on the wireless power transfer is thoroughly discussed. In the last part of the review, the state of the art in NFC-based chemical and biosensors is presented. NFC-based tags (or sensor tags) are mainly based on commercial or custom NFC ICs, which are used to harvest the energy from the RF field generated by the smartphone to power the electronics. Low-consumption colorimeters and potentiostats can be integrated into these NFC tags, opening the door to the integration of chemical sensors and biosensors, which can be harvested and read from a smartphone. The smartphone is also used to upload the acquired information to the cloud to facilitate the internet of medical things (IoMT) paradigm. Finally, several chipless sensors recently proposed in the literature as a low-cost alternative for chemical applications are discussed.

16 August 2021 in IEEE Access
Verified
Journal Article
Open access
ALAntonio Lazaro
Antonio Lazaro
Marc MartíMarc Martí
Marc Martí
RVRamon Villarino
Ramon Villarino
DGDavid Girbau
David Girbau
This work presents a seat-occupancy detection system based on a PCR (Pulsed Coherent Radar) at the unlicensed 60 GHz ISM band. The radar can measure distances with sub-millimeter resolution. Therefore, the system can detect the presence of people occupying the seats by measuring small movements of the body, such as those produced by breathing. In consequence, the system not only measures seat-occupancy but also breathing rate, which is estimated from the amplitude peaks after filtering the amplitude measured by the radar to remove the noise. The effect of the car vibrations and random body movement is experimentally studied. Measurements performed with adults, as well as with a baby emulator sitting in a child seat, are presented. Comparison of the system with another that measures the breath based on airflow shows good agreement and permits its validation.

10 March 2022 in Sensors
Verified
Journal Article
Open access
PDF file
ALAntonio Lazaro
Antonio Lazaro
APArnau Porcel
Arnau Porcel
Marc MartíMarc Martí
Marc Martí
RVRamon Villarino
Ramon Villarino
DGDavid Girbau
David Girbau
This work studies the feasibility of using backscatter-modulated tags to introduce false information into a signal received by a frequency-modulated continuous-wave (FMCW) radar. A proof-of-concept spoofing device was designed in the 24 GHz ISM band. The spoofing device was based on an amplifier connected between two antennas, and modulation was carried out by switching the amplifier bias. The use of an amplifier allowed us to increase the level of spoofing signal compared with other modulated backscattering methods. The simulated and experimental results show that our method has the ability to generate a pair of false targets at different ranges and velocities depending on the modulation frequency of the chosen tag, since sidebands appear due to this modulation. Countermeasures to detect the spoofing attack based on changes in the slope of the frequency sweep between frames are also proposed.

10 November 2021 in Sensors
Verified
Journal Article
Open access
PDF file
Marc MartíMarc Martí
Marc Martí
ALAntonio Lazaro
Antonio Lazaro
RVRamon Villarino
Ramon Villarino
DGDavid Girbau
David Girbau
The COVID-19 pandemic has highlighted a large amount of challenges to address. To combat the spread of the virus, several safety measures, such as wearing face masks, have been taken. Temperature controls at the entrance of public places to prevent the entry of virus carriers have been shown to be inefficient and inaccurate. This paper presents a smart mask that allows to monitor body temperature and breathing rate. Body temperature is measured by a non-invasive dual-heat-flux system, consisting of four sensors separated from each other with an insulating material. Breathing rate is obtained from the temperature changes within the mask, measured with a thermistor located near the nose. The system communicates by means of long-range (LoRa) backscattering, leading to a reduction in average power consumption. It is designed to establish the relative location of the smart mask from the signal received at two LoRa receivers installed inside and outside an access door. Low-cost LoRa transceivers with WiFi capabilities are used in the prototype to collect information and upload it to a server. Accuracy in body temperature measurements is consistent with measurements made with a thermistor located in the armpit. The system allows checking the correct placement of the mask based on the recorded temperatures and the breathing rate measurements. Besides, episodes of cough can be detected by sudden changes in thermistor temperature.

20 January 2021 in IEEE Access
Verified
Journal Article
Open access
ALAntonio Lazaro
Antonio Lazaro
Marc MartíMarc Martí
Marc Martí
RVRamon Villarino
Ramon Villarino
The aim of this paper is to propose a novel room-level localization approach to locate LoRa backscatter devices, which can be easily embedded into wearable devices or smartphones. The advantages of this system lie in its series of low-cost, low-power, low-complexity and long-range features. LoRa backscattering operates by alternatively connecting an antenna, through a switch, to two loads with high reflection coefficients and opposite phase. The result is a frequency shift of the LoRa incident signal equal to the backscatter switching frequency. The localization system comprises several LoRa receivers distributed among the rooms, a LoRa transmitter located at a central point and the backscatter device, which is carried or worn by a subject. The position of the LoRa backscatter device can be determined by comparing the received signal strength between all receivers. In order to improve the accuracy of the system, different machine learning classifiers were compared. System performance was tested in a real-life scenario, achieving an accuracy up to 89.7% using linear discriminant analysis (LDA).

24 May 2021 in Sensors
Verified
Journal Article
Open access
PDF file
ALAntonio Lazaro
Antonio Lazaro
Marc MartíMarc Martí
Marc Martí
RVRamon Villarino
Ramon Villarino
DGDavid Girbau
David Girbau
PPPedro de Paco
Pedro de Paco
This work proposes the use of a modulated tag for direct communication between two vehicles using as a carrier the wave emitted by an FMCW radar installed in the vehicle for advanced driver assistance. The system allows for real-time signals detection and classification, such as stop signal, turn signals and emergency lights, adding redundancy to computer video sensors and without incorporating additional communication systems. A proof-of-concept tag has been designed at the microwave frequency of 24 GHz, consisting of an amplifier connected between receiving and transmitting antennas. The modulation is performed by switching the power supply of the amplifier. The tag is installed on the rear of the car and it answers when it is illuminated by the radar by modulating the backscattered field. The information is encoded in the modulation switching rate used. Simulated and experimental results are given showing the feasibility of the proposed solution.