S The need for fully dense material with well-engineered microstructures has led to the promising emergence of innovative sintering technologies among which the Spark Plasma Sintering (SPS) is one of the most favorite. Unlike the conventional sintering processes, SPS takes advantage of a current flow passing through the sintering die and metallic powders by which fast densification with minimal grain growth and enhanced physicomechanical properties can be obtained. Albeit there is a growing interest in the exploitation of SPS in producing sufficiently consolidated metallic parts, no analytical review has been released over the effects of SPS parameters on the densification behavior, microstructure evolution, and resultant physicomechanical properties of metallic parts and their alloys. In the present review, recent developments and ongoing challenges in modeling the SPS of metallic systems are thoroughly explored. Then, the effects of main SPS parameters including sintering temperature, dwell time, heating rate, and pressure on the microstructure and physicomechanical properties of metals and alloys are comprehensively investigated. These properties are categorized into two groups: (i) physical properties including relative density, electrical and thermal conductivities; (ii) mechanical properties with a systematic focus on hardness, elastic modulus, and tensile, compressive, and bending strengths. In each section, the general trends along which SPS parameters grow to affect each corresponding property are comprehensively discussed. Additionally, various microstructural phenomena being more likely to occur at the given metallic systems are fully addressed. The present work seeks to elaborate on the aforementioned issues and provide an overview of the unresolved challenges and proposed solutions to them.

Spark plasma sintering (SPS) is widely used for the consolidation of different materials. Copper-based pseudo alloys have found a variety of applications including as electrodes in vacuum interrupters of high-voltage electric circuits. How does the kinetics of SPS consolidation for such alloys depend on the heating rate? Do SPS kinetics depend on the microstructure of the media to be sintered? These questions were addressed by the investigation of SPS kinetics in the heating rate range of 0.1 to 50 K/s. The latter conditions were achieved through flash spark plasma sintering (FSPS). We also compared the sintering kinetics for the conventional copper–chromium mixture and for the mechanically induced copper/chromium nanostructured particles. It was shown that, under FSPS conditions, the observed maximum consolidation rates were 20–30 times higher than that for conventional SPS with a heating rate of 100 K/min. Under the investigated conditions, the sintering rate for mechanically induced composite Cu/Cr particles was 2–4 times higher compared to the conventional Cu + Cr mixtures. The apparent sintering activation energy for the Cu/Cr powder was twice less than that for Cu–Cr mixture. It was concluded that the FSPS of nanostructured powders is an efficient approach for the fabrication of pseudo-alloys.

Laser powder bed fusion (L-PBF) stands out as a promising approach within the realm of additive manufacturing, particularly for the synthesis of CNT-AlSi10Mg nanocomposites. This review delves into a thorough exploration of the transformation in microstructure, the impact of processing variables, and the physico-mechanical characteristics of CNT-AlSi10Mg nanocomposites crafted via the L-PBF technique. Moreover, it consolidates a substantial corpus of recent research, proffering invaluable insights into optimizing L-PBF parameters to attain the desired microstructures and enhanced properties. The review centers its attention on pivotal facets, including the dispersion and distribution of CNTs, the formation of porosity, and their subsequent influence on wear resistance, electrical and thermal conductivity, tensile strength, thermal expansion, and hardness. In line with a logical progression, this review paper endeavors to illuminate the chemical composition, traits, and phase configuration of AlSi10Mg-based parts fabricated via L-PBF, juxtaposing them with their conventionally manufactured counterparts. Emphasis has been placed on elucidating the connection between the microstructural evolution of these nanocomposites and the resultant physico-mechanical properties. Quantitative data culled from the literature indicate that L-PBF-produced parts exhibit a microhardness of 151 HV, a relative density of 99.7%, an ultimate tensile strength of $70\times {10}^3 \frac{{\mathrm{mm}}^3}{\mathrm{N}.\mathrm{m}}$, and a tensile strength of 756 MPa.