Ratnak Sok

Dr. Ratnak Sok

Waseda University, Tokyo, Japan
+5
orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 September 2019 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
TKTakashi Kaminaga
Takashi Kaminaga
KYKyohei Yamaguchi
Kyohei Yamaguchi
Ratnak SokRatnak Sok
Ratnak Sok
JKJin Kusaka
Jin Kusaka
TYTakashi Youso
Takashi Youso
MYMasahisa Yamakawa
Masahisa Yamakawa
In order to improve thermal efficiency of spark ignition (SI) engines, an improved technology to avoid irregular combustion under high load conditions of high compression ratio SI engines is required. In this study, the authors focused on high pressure gasoline direct injection in a high compression ratio SI engine, which its rapid air-fuel mixture formation, turbulence, and flame speed, are enhanced by high-speed fuel spray jet. Effects of fuel injection pressure, injection and spark ignition timing on combustion characteristics were experimentally and numerically investigated. It was found that the heat release rate was drastically increased by raising the fuel injection pressure. The numerical simulation results show that the high pressure gasoline direct injection enhanced small-scale turbulent intensity and fuel evaporation, simultaneously. These two effects were considered as the main factors to increase the flame propagation speed, suggesting a new combustion concept different from conventional SI combustion controlled by in-cylinder bulk flow. This combustion method enables the delay of fuel injection and spark ignition timing up to near top dead center (TDC) which leads to avoid pre-ignition and knocking by shortening the end-gas reaction time. Therefore, it was shown that the irregular combustion in a high compression ratio SI engine could be avoided by utilizing high pressure gasoline injection, which leads to improve partial load thermal efficiency without affecting the high load performance.

1 December 2022 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
Ratnak SokRatnak Sok
Ratnak Sok
JKJin Kusaka
Jin Kusaka

14 February 2023 in Journal of Energy Resources Technology
Verified
Journal Article
Closed access
PDF file
Ratnak SokRatnak Sok
Ratnak Sok
JKJin Kusaka
Jin Kusaka
HNHisaharu Nakashima
Hisaharu Nakashima
HMHidetaka Minagata
Hidetaka Minagata
PDPavlos Dimitriou
Pavlos Dimitriou
Jinlong LiuJinlong Liu
Jinlong Liu


9 September 2019 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
MTMasashi Tanamura
Masashi Tanamura
SNShintaro Nakai
Shintaro Nakai
MNMahoko Nakatsuka
Mahoko Nakatsuka
STShota Taki
Shota Taki
KOKohei Ozawa
Kohei Ozawa
JKJin Kusaka
Jin Kusaka
Pre-chamber spark ignition technology can stabilize combustion and improve thermal efficiency of lean burn natural gas engines. During compression stroke, a homogeneous lean mixture is introduced into pre-chamber, which separates spark plug electrodes from turbulent flow field. After the pre-chamber mixture is ignited, the burnt jet gas is discharged through multi-hole nozzles which promotes combustion of the lean mixture in the main chamber due to turbulence caused by high speed jet and multi-points ignition. However, details mechanism in the process has not been elucidated. To design the pre-chamber geometry and to achieve stable combustion under the lean condition for such engines, it is important to understand the fundamental aspects of the combustion process. In this study, a high-speed video camera with a 306 nm band-pass filer and an image intensifier is used to visualize OH* self-luminosity in rapid compression-expansion machine experiment. The results show that the OH* self-luminosity is observed in outer edge of the jet, while the luminosity in the jet temporarily weakens because the turbulent jet is exposed to low temperature surrounding in the main chamber. After that, the OH* luminosity is spontaneously increased near the wall due to auto-ignition when the gas temperature increases. In order capture this self-luminosity in multi-dimensional simulation, OH* formation and deactivation reactions are introduced into a commercial 3D-CFD code coupled with detailed chemistry to compare the measured images with the simulated ones. As a result, the OH* self-luminous distributions obtained by the 3D-CFD calculation have reasonable agreement with the measurement showing fundamental understanding on chemical reaction, heat release and temperature distribution of the jet.

25 March 2019 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
Ratnak SokRatnak Sok
Ratnak Sok
KYKyohei Yamaguchi
Kyohei Yamaguchi
JKJin Kusaka
Jin Kusaka
This paper focuses on an assessment of predictive combustion model using a 0D/1D simulation tool under high load, different excess air ratio λ , and different combustion stabilities (based on coefficient of variation of indicated mean effective pressure COVimep). To consider that, crank angle resolved data of experimental pressure of 500 cycles are recorded under engine speed 1000 RPM and 2000 RPM, wide-open throttle, and λ=1.0, 1.42, 1.7, and 2.0. Firstly, model calibration is conducted using 18 cases at 2000 RPM using 500 cycle-averaged in-cylinder pressure to find optimized model constants. Then, the model constants are unchanged for other cases. Next, different cycle-averaged pressure data are used as inputs in the simulation based on the COVimep for studying sensitivity of the turbulent model constants. The simulation is conducted using 1D simulation software GT-Power. Firstly, a three-pressure analysis (TPA) model (intake, in-cylinder, exhaust) for experimental prediction and optimization of burn rate shape are studied. Boundary conditions such as the three pressure histories, intake/exhaust valves timings, boundary temperatures, and exhaust gas emissions are used as model inputs. Errors of indicated thermal efficiency, indicated mean effective pressure, and CA50 are within 3%. Predicted parameters from the TPA model such as air volumetric efficiency, trapped air/fuel vapor mass, trapped residual gas fraction, tumble, and surface temperature of the piston, head, and valves are used as initializations in the predictive combustion model. A built-in flame propagation model, termed as SITurb, is investigated whether it can replicate the in-cylinder pressure and burn rate shapes. A revised laminar flame speed correlation of five-component gasoline surrogate is incorporated in the combustion model via an encrypted dynamic link library file. The results show that thermodynamic histories of the combustion are reproducible under high load and stoichiometric-to-ultra-lean conditions. Under all cases, only turbulent flame speed multiplier needs to be calibrated.