Congxin Chen

Congxin Chen


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 May 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Zhanghao RenZhanghao Ren
Zhanghao Ren
CCCongxin Chen
Congxin Chen
Chaoyi SunChaoyi Sun
Chaoyi Sun
YWYue Wang
Yue Wang
Earthquakes are a major external factor that induce landslides. In order to systematically study the dynamic effects and failure mechanism of anti-dip bedding rock slopes (the slope trend is the same as the joint trend, while the slope dip direction is opposite to the joint dip direction) under seismic action (as well as the spatial effects of the structural planes in the anti-dip bedding rock slopes), three-dimensional (3D) discrete-element numerical calculations were performed to analyze anti-dip bedding rock slopes with different slope angles, joint angles, and joint trends subjected to the action of natural seismic and sinusoidal waves. The results were analyzed to investigate the amplification effect, change in Fourier spectrum, failure mechanism, and permanent displacement of the slope under the applied seismic action. The permanent displacement of the slope was calculated using Newmark’s method and the results obtained were discussed and compared with those obtained from a dynamic analysis performed using the 3D discrete-element method. The results showed that the regularity of the spatial distribution of the amplification effect was less clear than that encountered in the planar problem (unidirectional or bidirectional dynamical loading), and this leads to the effect of having an overall rhythmical nature. The seismic wave decays in the high-frequency part from the bottom up of the slope, while the dominant frequency of the seismic wave decreases. The value of the permanent displacement obtained using Newmark’s method is much smaller than that obtained using the dynamic 3D discrete-element analysis approach. The angle between the joint and slope trends has a significant effect on the amplification effect, failure mode, permanent displacement, and stability of slopes subjected to seismic action.

9 January 2021 in Sensors
Verified
Journal Article
Open access
PDF file
YZYapeng Zhang
Yapeng Zhang
CCCongxin Chen
Congxin Chen
YZYun Zheng
Yun Zheng
YSYong Shao
Yong Shao
Chaoyi SunChaoyi Sun
Chaoyi Sun
Joints between diaphragm wall panels are weak spots in wall construction. It is essential that potential leak sites are detected prior to excavation. In this study, a novel leak detection and monitoring system is presented that is based on fiber Bragg grating (FBG) sensing technology. A field study was performed in a deep excavation supported by diaphragm walls (in Hohhot, China) to validate the feasibility and effectiveness of the proposed method. Two schemes were trialed; one using pipes made of stainless steel, and one used a pipeless method. The results of the field study are presented and discussed. They show that potential leak sites in the wall joints could be determined prior to excavation using the proposed detection method. Stainless steel is a good material to use to make the detection tube because it can protect the FBG sensors and heating belts from damage and is more sensitive to water leakage. The field study provides good evidence for the feasibility of the new detection system. It also provides valuable experience for the field application of the system and has generated useful data to use in follow-up work.

9 September 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
Zhanghao RenZhanghao Ren
Zhanghao Ren
CCCongxin Chen
Congxin Chen
YZYun Zheng
Yun Zheng
Chaoyi SunChaoyi Sun
Chaoyi Sun
JYJiahao Yuan
Jiahao Yuan
As a result of earthquakes, the deformation and failure caused by anti-dip bedding rock slopes are large, and their seismic dynamic response law is complex. Using the three-dimensional discrete element numerical analysis software 3DEC, the influence of seismic wave parameters on the dynamic response of anti-dip bedding rock slopes was systematically studied, with special focus on the influence of the angle between seismic wave incidence direction and slope trend on the dynamic response of anti-dip bedding rock slopes under three-dimensional conditions. The orthogonal test was designed to conduct sensitivity analysis of five seismic parameters, including seismic wave amplitude, incidence angle of the S-wave, frequency, duration, and the time difference between the P-wave’s and the S-wave’s peak. The results revealed that the S-wave’s amplitude As and the holding time T of the seismic wave are positively correlated with the acceleration amplification factor of the slope, and the incident direction γ of the S-wave is negatively correlated with the acceleration amplification factor of the slope. The increase of seismic wave frequency f and the time difference Δt between the P-wave’s and the S-wave’s peak lead to the first increase and then decrease of the Y-directional displacement of the slope. The sensitivity of each seismic wave parameter to the Y-directional acceleration amplification factor at the shoulder of anti-dip bedding rock slopes in earthquake conditions is ordered as follows: S-wave’s amplitude As > frequency f > S-wave’s incidence angle γ > the time difference Δt > holding time T. the study results provide reference and basis for stability evaluation and engineering design of anti-dip bedding rock slopes in areas with high seismic intensity.

15 March 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YZYapeng Zhang
Yapeng Zhang
CCCongxin Chen
Congxin Chen
MLMeiqing Lei
Meiqing Lei
YZYun Zheng
Yun Zheng
HZhaina zhang
haina zhang
YSYong Shao
Yong Shao
A new form of retaining system for use in deep excavations in crowded cities is proposed in this paper. The new system, which we have coined the herringbone retaining system (HRS) involves the use of vertical and batter piles, capping beams, and wales. A numerical study was conducted (using the finite difference tool FLAC3D) to investigate various aspects of the behavior of the new system and reveal the mechanisms responsible for it. The HRS method was compared subsequently to two other commonly-used systems: the cantilever retaining structure (CRS) and horizontal-strutted retaining structure (HSRS). The results show that using the HRS method significantly reduces the deformation of the vertical piles and bending moments acting on them. More specifically, the maximum values of the deformation and bending moment were calculated to be 4.5% and 23.1% of the corresponding CRS values, respectively (the corresponding figures calculated for the HSRS method are 5.3% and 19.7%, respectively), so the HRS and HSRS methods provide similar levels of support. Finally, a real-world application of the system was presented to provide a valuable reference for the future use of HRS.

1 August 2026 in Journal of Mountain Science
Verified
Journal Article
Closed access
PDF file
KFKai Fan
Kai Fan
XLXiumin Liu
Xiumin Liu
CCCongxin Chen
Congxin Chen
ZHZiyi Huang
Ziyi Huang