The composite-aluminum hybrid bolted structures are widely used in aircraft. Due to low molding accuracy of composite components, gaps always occur between components during assembly. In this case, the bolt connection can cause a complex strain and stress state of component. It may adversely affect the mechanical properties or cause local damage of the structure. A simplified model of the composite-aluminum assembly structure was established in this paper. Then, the influence of forced assembly, liquid shim, and peelable fiberglass shim on the strain and stress state of the composite-aluminum hybrid bolted structure was studied. A bolt connection experimental device was designed to apply a preload to the specimen. The strain field on the specimen surface was measured using the 3D-DIC strain measurement system. The finite element model was established to study the interlaminar stress and damage state of composite laminates. It is found that the strain of specimen in the -direction is mainly affected by the bending deformation, while the strain in the -direction is mainly affected by the compression of bolt head. For composite laminates, the strain value in the -direction can be reduced by 8.31%-70.97% with shims. As for the strain value in the -direction, the liquid shim can only reduce it up to 23.93%when the gap is large. In addition, the liquid shim and peelable fiberglass shim cannot reduce the stress value of all interlaminar elements, but it can make the stress distribution more uniform and improve the stress state of the interlaminar element when the shim was more than 0.8 mm.
The success of an autoclave process is related to the temperature characteristics of the mold. An inhomogeneous temperature field in the mold affects the quality of composite parts, which may lead to residual stress, voids, and other manufacturing defects of composite parts. In order to meet high-quality production demands, the temperature field in a mold should be investigated precisely. The temperature distribution in a large frame mold is critically evaluated in this work. Then, a method to control the temperature distribution in a large frame mold is proposed. A computational fluid dynamics (CFD) model of the autoclave process is developed to predict the temperature evolution of the large frame mold. The model is validated by experimental results, which shows good agreement with a relative difference of 5.92%. The validated CFD model is then applied to analyze the temperature distribution characters in the mold with different control conditions. The results show that the temperature difference decreases by 13.3% when the mold placement angle is changed from 180 to 168°.
31 March 2019 in International Journal of Aerospace Engineering
A typical aircraft panel is the assembly consisting of a multitude of thin and lightweight compliant parts. In panel assembly process, part-to-part locating scheme has been widely adopted in order to reduce fixtures. By this locating scheme, a part is located onto the pre-fixed part/subassembly by determinant assembly (DA) holes, and temporary fasteners (e.g., spring pin) are used for joining these DA hole-hole pairs. The temporary fasteners can fasten DA hole-hole pairs in the axial and radial directions of DA holes. The fastening in the radial directions is realized by the expansion of temporary fasteners. Although the usage of temporary fasteners helps reduce the positional differences between hole-hole pairs, their clamping forces thereby may lead to elastic deformation of compliant parts/subassemblies. Limited research has been conducted on such elastic deformation produced by temporary fastener and its influence on assembly dimensional quality. This paper proposes a novel rigid-compliant variation analysis method for aircraft panel assembly, incorporating the deformation in part-to-part locating process. Based on the kinematic theory and linear elasticity deformation assumption, the variation propagation through the locating process, as well as the entire assembly process of an aircraft panel, is formulated. Then, the statistical variation analysis is performed with Monte Carlo (MC) simulation. Finally, the proposed method is validated by a case study. The result shows the deformation in the part-to-part locating process significantly impacts the assembly variations, and our method can provide a more accurate and reliable prediction.
The finger lock structure of aircraft landing gear is prone to wear and failure during repeated locking and unlocking processes, which is disastrous for the service safety of the aircraft. At present, the commonly used material for finger locks in the industry is 30CrMnSiNi2A, which has a short wear life and high maintenance costs. It is crucial to develop effective methods to improve the wear resistance of 30CrMnSiNi2A finger locks. This work explores the wear resistance and wear mechanisms of different metallic coatings such as chromium, nickel, and cadmium–titanium on the surface of a 30CrMnSiNi2A substrate. The effects of load and wear time on the wear behavior are also discussed. The results indicated that the wear resistance of the chromium coating was the maximum. When the load was 80 N and 120 N, the wear mechanisms were mainly oxidation and adhesive. For greater loads, the wear mechanism of the coating after failure was mainly abrasive and oxidation, and the wear was extremely severe. When the load was 80 N, for a greater loading time, the wear mechanisms were mainly oxidation and adhesive.
About Me
Prof. Luling An is a professor at the Nanjing University of Aeronautics and Astronautics, College of Mechanical and Electrical Engineering. He graduated from Nanjing University of Aeronautics and Astronautics in 1982 with a Bachelor's degree in Mechanical Design; graduated from Shandong University of Technology in 1985 with a Master's degree in Mechanical Engineering; and graduated from Nanjing University of Aeronautics and Astronautics in 2001 with a Doctorate in Aerospace Manufacturing Engineering. From 1985 to 1997, he taught at Shandong Mining Institute (now Shandong University of Science and Technology); from 2001 to present, he has been an Associate Professor and Professor at the School of Mechanical and Electrical Engineering of Nanjing University of Aeronautics and Astronautics. His research areas include digital design and manufacturing, rapid tooling design, and aircraft assembly technology. He has published more than 100 papers, obtained two authorized invention patents, and won one second prize in national teaching achievements, and five second prizes and one third prize in provincial and ministerial science and technology progress.
Prof. Luling An is a professor at the Nanjing University of Aeronautics and Astronautics, College of Mechanical and Electrical Engineering. He graduated from Nanjing University of Aeronautics and Astronautics in 1982 with a Bachelor's degree in Mechanical Design; graduated from Shandong University of Technology in 1985 with a Master's degree in Mechanical Engineering; and graduated from Nanjing University of Aeronautics and Astronautics in 2001 with a Doctorate in Aerospace Manufacturing Engineering. From 1985 to 1997, he taught at Shandong Mining Institute (now Shandong University of Science and Technology); from 2001 to present, he has been an Associate Professor and Professor at the School of Mechanical and Electrical Engineering of Nanjing University of Aeronautics and Astronautics. His research areas include digital design and manufacturing, rapid tooling design, and aircraft assembly technology. He has published more than 100 papers, obtained two authorized invention patents, and won one second prize in national teaching achievements, and five second prizes and one third prize in provincial and ministerial science and technology progress.