Rawad Deeb

Dr. Rawad Deeb

National Research University (Moscow Power Engineering Institute)
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2021 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
RDRawad Deeb
Rawad Deeb
The effect of angle of attack on fluid flow characteristics around a single drop-shaped tube is studied for the first time experimentally and numerically. The study covers the Reynolds numbers Re = (13.2–30.4) × 103 and flow angles of attack (θ = 0°–50° and 130°–180°). The results of the drop-shaped tube were compared with those of a circular tube having the same equivalent diameter. Numerical computational fluid dynamics modeling using the finite volume discretization method is used to predict the flow pattern around tubes. It was found that the drop-shaped tubes delay the separation of the boundary layer from the tube wall. The drop-shaped tube showed its superiority over a circular tube in terms of reduced drag and friction factor under the same operating conditions. The values of the friction factor for the arrangement of θ = 50°, 150°, and 170° are lower than those obtained for a circular tube by about 2.6–2.9, 2.6, and 2.6–3.2 times, respectively.

1 February 2022 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
RDRawad Deeb
Rawad Deeb

28 November 2022 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
RDRawad Deeb
Rawad Deeb


1 June 2022 in Physics of Fluids
Verified
Journal Article
Closed access
RDRawad Deeb
Rawad Deeb
The purpose of this study is to clarify heat transfer and fluid flow behavior across six-row mixed tube bundles. The tube bundle consists of circular and drop-shaped cross sections in a staggered arrangement. The Reynolds number Re for the flow is varied from 1.78 × 103 to 18.72 × 103. Six cases of the mixed tube bundle were considered. The results of the mixed tube bundles were compared with those of the circular (case I) and drop-shaped ones (case II). The Ansys Fluent software package was utilized to predict the flow pattern over the tube bundles. The results of the numerical simulation showed that the cross-sectional shape of the tubes and their location in the bundle significantly affect the heat transfer and pressure drop in the bundle. Case IV (circular tubes in the first, third, and fifth rows and drop-shaped tubes in the second, fourth, and sixth rows) increases the average Nusselt number Nu¯ by about 1.11%–8.10% and 47.86%–49.04% compared to that of the circular and drop-shaped tube bundles, respectively. Case VII (drop-shaped tubes in the first, second, fourth, and sixth rows and circular tubes in the third and fourth rows) has the lowest friction factor f compared to the other cases of circular and mixed tube bundles. Moreover, the maximum values of the thermal–hydraulic performance ε were achieved for case IV at Re = 1.78 × 103 and the case VII at Re >1.78 × 103, which were about 14.55% and (2.08–4.49)%, respectively, higher than those obtained for the drop-shaped tube bundle. Generalized correlations of Nu¯, f, and ε for the studied mixed tube bundles were predicted.

1 November 2019 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
RDRawad Deeb
Rawad Deeb
DSD V Sidenkov
D V Sidenkov
Tube bundles can be used as a separation heat exchanger in the “organic” Rankine cycle power plants (ORC), while the hot gas passes over the outer surface, and the working substance ORC flows inside the tubes. A numerical study has been conducted to clarify heat transfer and hydrodynamics of a cross-flow heat exchanger with staggered drop-shaped tubes at different flow angles of attack (θ). A mathematical and numerical model in software package ANSYS has been developed for numerical evaluation of heat transfer and flow field of a bundle of drop-shaped tubes, with taking into account the strain caused by different pressures inside and outside the tubes. The results of numerical simulation of pressure, velocity, temperature distribution in the tube’s bundle had provided the development of equation to determine the average Nusselt number (Nu) in terms of Reynolds number (Re), Prandtl number (Pr) and angle of attack.