In order to study the dynamic stress distribution and the fracture area of rock around the tunnel under different orientations of blasting disturbance, AUTODYN finite difference method software was used to conduct numerical simulation research. Gauge monitoring points were set around the numerical model of the tunnel to conduct real-time monitoring of the stress distribution, displacement and fracture area of the tunnel. Based on the analysis of the stress wave propagation law, the following conclusions are obtained: (1) under the condition of the same blasting loads, the stress and displacement of the tunnel is relatively small when the blasting disturbance source is located above the roof, i.e., the stress state of the tunnel is relatively stable and the fracture area around the tunnel is minimal; (2) from the uniaxial stress around the tunnel and the tunnel peripheral displacement, it can be seen that the displacement caused by horizontal direction stress of the tunnel is the largest, and the deformation is mainly concentrated above the floor and at the shoulder, while the vertical wall part has almost no deformation; (3) for brittle materials such as rock, the arch-shaped stress-bearing surface is more likely to disperse stress, while the straight wall and flat floor of the tunnel cannot well disperse stress, resulting in uneven stress on the stress-bearing surface, uncoordinated deformation and ultimately, failure.

The fracturing technology for increasing gas production based on hydrate reservoir reconstruction has been proven to have the application prospect of hydrate production. The main content of this work is to study the influence mechanism between multiple production wells after fracturing the reservoirs around horizontal wells. Simulation results indicated that the gas production rates and cumulative volume of released gas by using hydraulic fracturing were both higher than that by using the traditional depressurization method. The average gas-to-water ratio in this work has broken through the technical bottleneck of exploiting hydrate only by the traditional depressurization method. After the rock matrix around the horizontal well was fractured, the permeability of the reservoir in the fracturing area would be increased; thus, the propagation distance of pressure drop would be promoted. In addition, the penetration of the hydrate decomposition area between horizontal production wells was conducive to promoting the flow of decomposed gas and water to production wells. Besides, the hydraulic fracturing method to increase the permeability of the reservoir around the production well is very effective for the gas production of low-permeability natural hydrate deposits. The best distance between production wells was recommended to be 45~60 m, and it was recommended to provide appropriate heat in the area between the two wells to accelerate the decomposition of hydrate.

To study the shear damage and failure characteristics of red sandstone under different normal stress conditions, the failure process of sandstone under three different shear angles (50°, 55°, 60°) were studied by using variable angle shear test device. The shear stress-deformation curves and failure characteristics of sandstone were obtained, and the relationships between shear cracks and acoustic emission impact times, amplitude, peak frequency were established. With the increase of shear angle, the normal stress, shear stress and peak shear stress decrease gradually. The development of micro-cracks in the shear plane appear more earlier. The high frequency signal decreases significantly, which may have a significant corresponding relationship with the rock friction and shear effect. The failure mode of rock changes from plasticity to brittleness. The amplitude changes are concave, and more acoustic emission energy is released at compaction stage and plastic(failure) stage. The rock spalling mainly occur in the penetrating area of main and secondary cracks surrounding the two ends of specimen. The spalling degree was obviously weakened with the increase of shear angle. The results have important guiding value for judging and predicting the instability mechanism of rock engineering.

In rock blasting for engineering applications—such as quarrying and tunnel construction—blasting is often detonated in carefully timed sequences to optimize rock fragmentation. This study examines Model I crack propagation in tunnel blasting sections with empty holes using circular PMMA (Polymethyl Methacrylate) samples containing pre-made initial cracks and empty holes. The distance between holes was varied from 10 mm to 30 mm. Using AUTODYN V18.0 numerical simulation software, how these holes affect crack initiation, propagation, and the surrounding stress field were analyzed. Key findings include the following: (a) Blasting stress waves diffract and reflect off empty hole edges, creating overlapping pressure zones between adjacent empty holes. Within a critical range of the empty hole distance, wider hole distance leads to slower stress wave propagation due to increased dispersion. (b) The empty holes weaken the stress concentration at crack tips, with greater distance further reducing peak strength. Proximal crack tips experience more pronounced stress field alterations than distal ones. (c) Holes hinder crack initiation, with the required stress intensity factor rising in near-linear proportion to hole separation distance.