Slewing bearings are widely used in industry to provide rotary support and carry heavy load. The load-carrying capacity is one of the most important features of a slewing bearing, and needs to be calculated cautiously. This paper investigates the effect of mesh size on the finite element (FE) analysis of the carrying capacity of slewing bearings. A local finite element contact model of the slewing bearing is firstly established, and verified using Hertz contact theory. The optimal mesh size of finite element model under specified loads is determined by analyzing the maximum contact stress and the contact area. The overall FE model of the slewing bearing is established and strain tests were performed to verify the FE results. The effect of mesh size on the carrying capacity of the slewing bearing is investigated by analyzing the maximum contact load, deformation, and load distribution. This study of finite element mesh size verification provides an important guidance for the accuracy and efficiency of carrying capacity of slewing bearings.
12 May 2020 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
This article conceptually proposes a new method to tune the resonance frequency of piezoelectric vibration energy harvesters, in which the supporting position of the vibrator can be adjusted for frequency tuning. The corresponding analytical model is established to predict the performances of the harvester based on the principles of energy. First, the equivalent stiffness and mass of the vibrator in bending mode are derived explicitly for the different supporting positions. A simple analysis method is then established for the frequency, output voltage, and output power. Finally, some numerical examples are given to demonstrate the presented method. The results are also compared with those by finite element method and good agreement is observed.
17 May 2021 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
An in-depth study of friction and wear requires analysis of the surface morphologies and contact status of friction pairs in mechanical systems. The bearing area curve is introduced for the calculation of wear, and combined with the concept of repositioning. The application of fast calculation of wear amount and improved three-dimensional characterization of a bearing area curve is achieved by this new method. The best roughness surface is used as the target surface to extract the target bearing area curve. The influence of microtexture parameters on the bearing area curve is studied to determine the optimal microtexture parameters. The test results show that a matching texture surface has a short run-in time and the lowest friction coefficient after stabilization among the surfaces studied herein, and the presence of a texture changes the wear mechanism from the original adhesive wear to abrasive wear and improves the tribological performance. The best texture parameters and laser process parameters are determined, which provide new ideas for the optimal design of surface topography.
12 August 2020 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Three-row roller slewing bearings are the core components of large-scale rotating equipment. A large structural size and heavy load conditions require an extremely high carrying capacity. The inner ring of the slewing bearing is divided into upper and lower parts in this paper, which is the same as the actual working condition and effectively avoids the increase in the stiffness caused by simplifying the inner ring as a whole. Different bolt models and bolt preloads, the effect of the roller diameter on the stiffness and the strength of the support structure are analysed to improve the calculation accuracy and efficiency of the carrying capacity of the slewing bearing. Calculation formulas based on engineering experience and strain measurement are used to verify the validity of the finite element model. The research shows that the carrying capacity of the slewing bearing is affected by the supporting structure; as the bolt preload increases, the overall deformation of the slewing bearing decreases, and the load distribution is smoother. The key structures of the slewing bearing are studied, which is conducive to improving the carrying capacity and optimizing the design.
28 January 2021 in Advances in Mechanical Engineering
Slewing bearings are critical components of rotating equipment. Large structure sizes and heavy working load conditions require an extremely high load-bearing capacity and reliability. Overall and local contact finite element models of slewing bearings are verified by the empirical formula and Hertz contact theory. Validated finite element models are used to analyse the influence of the elastic material (E 1) and elastoplastic material parameters (EP 1, EP 2 and EP 3) on the load carrying capacity. The following conclusions are obtained by comparing the maximum contact load, the contact stress, the load distribution and the full-circle deformation. The influence of the material parameters on the slewing bearing is investigated to improve the analysis accuracy of the carrying capacity of the slewing bearings.