A large contribution to the aerodynamic drag of a vehicle arises from the failure to fully recover pressure in the wake region, especially on squareback configurations. A degree of base pressure recovery can be achieved through careful shape optimisation, but the freedom of an automotive aerodynamicist to implement significant shape changes is limited by a variety of additional factors such styling, ergonomics and loading capacity. Active flow control technologies present the potential to create flow field modifications without the need for external shape changes and have received much attention in previous years within the aeronautical industry and, more recently, within the automotive industry. In this work the influence of steady blowing applied at a variety of angles on the roof trailing edge of a simplified ¼ scale squareback style vehicle has been investigated. Hot-wire anemometry, force balance measurements, surface pressure measurements and PIV have been used to investigate the effects of the steady blowing on the vehicle wake structures and the resulting body forces. The energy consumption of the steady jet is calculated and is used to deduce an aerodynamic drag power change. Results show that overall gains can be achieved; however, the large mass flow rate required restricts the applicability of the technique to road vehicles. Means by which the mass flow rate requirements of the jet may be reduced are discussed and suggestions for further work put forward.

As vehicle manufacturers work to reduce energy consumption of all types of vehicles, external vehicle aerodynamics has become increasingly important. Whilst production vehicle shape optimisation methods are well developed, the need to make further advances requires deeper understanding of the highly three-dimensional flow around bluff bodies. In this paper, the wake flow of a generic bluff body, the Windsor body, based on a square-back car geometry, was investigated by means of balance measurements, surface pressure measurements and 2D particle image velocimetry planes. Changes in the wake topology are triggered by the application of short tapers (4 % of the model length) to the top and bottom edges of the base, representing a shape optimisation that is realistic for many modern production vehicles. The base drag is calculated and correlated with the aerodynamic drag data. The results not only show the effectiveness of such small devices in modifying the time average topology of the wake but also shed some light on the effects produced by different levels of upwash and downwash on the bi-stable nature of the wake itself.

Square-back shapes are popular in the automotive market for their high level of practicality. These geometries, however, are usually characterised by high drag and their wake dynamics present aspects, such as the coexistence of a long-time bi-stable behaviour and short-time global fluctuating modes that are not fully understood. In the present paper, the unsteady behaviour of the wake of a generic square-back car geometry is characterised with an emphasis on identifying the causal relationship between the different dynamic modes in the wake. The study is experimental, consisting of balance, pressure, and stereoscopic PIV measurements. Applying wavelet and cross-wavelet transforms to the balance data, a quasi-steady correlation is demonstrated between the forces and bi-stable modes. This is investigated by applying proper orthogonal decomposition to the pressure and velocity data sets and a new structure is proposed for each bi-stable state, consisting of a hairpin vortex that originates from one of the two model’s vertical trailing edges and bends towards the opposite side as it merges into a single streamwise vortex downstream. The wake pumping motion is also identified and for the first time linked with the motion of the bi-stable vortical structure in the streamwise direction, resulting in out-of-phase pressure variations between the two vertical halves of the model base. A phase-averaged low-order model is also proposed that provides a comprehensive description of the mechanisms of the switch between the bi-stable states. It is demonstrated that, during the switch, the wake becomes laterally symmetric and, at this point, the level of interaction between the recirculating structures and the base reaches a minimum, yielding, for this geometry, a \(7\%\) reduction of the base drag compared to the time-averaged result.

In this paper, the unsteady wake of a simplified square-back vehicle, with and without wheels, is investigated using large-scale tomographic particle image velocimetry, at a Reynolds number of (based on the model height). In the no-wheel case, the time-averaged wake features a balanced toroidal shape, with a good level of symmetry in both vertical and lateral directions. However, analysis of the wake dynamics shows this widely accepted result to be a poor model of the wake structure. Application of proper orthogonal decomposition to the unsteady data reveals the existence of the widely reported bi-stable behaviour, consisting of random switches between two lateral symmetry-breaking states. For the first time, the three-dimensional topology of each state is fully characterised and the changes in wake topology during the switches between bi-stable states are also described. Each symmetry-breaking state is shown to feature a characteristic ‘hairpin vortex’ structure that is the result of the merging of two horseshoe vortices, aligned with the vertical edges of the model base. The mutual interactions between these vortices are found to be at the origin of the bi-stable mode. The vertical symmetry is lost when wheels are added to the model, resulting in the formation of an upwash-dominated wake. The bi-stable behaviour is removed but considerable mobility in the near wake remains, in the form of a swinging motion of the rear recirculation.

The design methodology and performance of Loughborough University’s new 1·9m × 1·3m, indraft wind tunnel is discussed in the following paper. To overcome severe spatial and financial constraints, a novel configuration was employed, with the inlet and exit placed adjacent to each other and opened to atmosphere. Using a fine filter mesh, honeycomb, two turbulence reduction screens and a contraction ratio of 7·3, flow uniformity in the working area of the jet at 40ms^-1is shown to be within 0·3% deviation from the mean velocity, with turbulence intensity in the region of 0·15%. Working section boundary layer characteristics are shown to be consistent with that of a turbulent boundary layer growing along a flat plate, which originates at the point of inflection of the contraction. A maximum velocity of 46ms^-1was achieved from a 140kW motor, compared to a prediction of 44ms^-1, giving an energy ratio of 1·42. Comparison between theoretical and measured performance metrics indicate differences between the way modules perform when part of a wind tunnel system compared to data gathered from test rigs.

A large contribution to the aerodynamic drag of a vehicle is the loss of pressure in the wake region, especially on square-back configurations. Wake pressure recovery can be achieved by a variety of physical shape changes, but with vehicle shapes becoming ever more aerodynamically efficient research into active technologies for flow manipulation is becoming more prominent. The aim of the current paper is to generate an understanding of how an optimized roof trailing edge, in the form of a chamfer, can reduce wake size, increase base pressures and reduce drag. A comprehensive study using PIV (Particle Image Velocimetry), balance measurements and static pressure measurements was performed in order to investigate the flow and wake structure behind a simplified car model. Significant reductions in C d are demonstrated and directly related to the measured base and slant pressures. The PIV data shows both the time averaged structure of the wake and the unsteady shedding associated with the upper separation. The work is intended to act as a precursor for quantifying the effectiveness of active technologies such as Synthetic Jets which aim to achieve the same goals as this passive optimization, but require an energy input.