Most of today’s water supply systems are based on plastic pipes. They are characterized by the retarded strain (RS) that takes place in the walls of these pipes. The occurrence of RS increases energy losses and leads to a different form of the basic equations describing the transient pipe flow. In this paper, the RS is calculated with the use of convolution integral of the local derivative of pressure and creep function that describes the viscoelastic behavior of the pipe-wall material. The main equations of a discrete bubble cavity model (DBCM) are based on a momentum equation of two-phase vaporous cavitating flow and continuity equations written initially separately for the gas and liquid phase. In transient flows, another important source of pressure damping is skin friction. Accordingly, the wall shear stress model also required necessary modifications. The final partial derivative set of equations was solved with the use of the method of characteristics (MOC), which transforms the original set of partial differential equations (PDE) into a set of ordinary differential equations (ODE). The developed numerical solutions along with the appropriate boundary conditions formed a basis to write a computer program that was used in comparison analysis. The comparisons between computed and measured results showed that the novel modified DBCM predicts pressure and velocity waveforms including cavitation and retarded strain effects with an acceptable accuracy. It was noticed that the influence of unsteady friction on damping of pressure waves was much smaller than the influence of retarded strain.

This paper concerns the start-up process of a hydrostatic transmission with a fixed displacement pump, with particular emphasis on dynamic surplus pressure. A numerically controlled transmission using a proportional directional valve was analysed by simulation and experimental verification. The transmission is controlled by the throttle method, and the variable resistance is the throttling gap of the proportional spool valve. A mathematical description of the gear start-up process was obtained using a lumped-parameters model based on ordinary differential equations. The proportional spool valve was described using a modified model, which significantly improved the performance of the model in the closed-loop control process. After assuming the initial conditions and parameterization of the equation coefficients, a simulation of the transition start-up was performed in the MATLAB–Simulink environment. Simulations and experimental studies were carried out for control signals of various shapes and for various feedback from the hydraulic system. The pressure at the pump discharge port and the inlet port of the hydraulic motor, as well as the rotational speed of the hydraulic motor, were analysed in detail as functions of time. In the experimental verification, complete measuring lines for pressure, speed of the hydraulic motor, flow rate, and temperature of the working liquid were used.

In pressurised pipeline systems, various water hammer events commonly occur. This phenomenon can cause extensive damage or even lead to a failure of the pumping system. The aim of this work is to experimentally re-examine the possibility of using an additional polymeric pipe, installed at the downstream end of the main pipeline, to control water hammer. A previous study on this topic investigated additional polymeric pipes connected to the hydraulic system with a short joint section of the same diameter as the main pipeline. In the current research, a different method of including an additional pipe was considered which involved connecting it with a pipe of a smaller diameter than the main pipeline. Three additional HDPE pipes, with different volumes, were investigated. The performance of the devices was studied for hydraulic transients induced by both rapid and slow, manual valve closures. Experimental results show that the additional polymeric pipe can provide significant pressure surge damping during rapid water hammer events. As the valve closing time lengthens, the influence of the additional pipe on the maximum pressure increase is reduced. The additional HDPE pipe does not provide notable protection against hydraulic transients induced by slow valve closure in terms of reducing the first pressure peak. No relationship between the volume of the additional pipe and the damping properties was noticed. The observed pressure oscillations were used to evaluate a one-dimensional numerical model, in which an additional pipe is described as a lumped parameter of the system. The viscoelastic properties of the device were included using the one element Kelvin–Voigt model. Transient flow equations were solved with the implicit method of characteristics. Calculation results demonstrate that this approach allows one to reasonably reproduce unsteady flow oscillations registered during experiments in terms of the maximum pressure increase and pressure wave oscillation period.

This paper investigates dynamic pressure waveforms in hydraulic hoses. Steel hoses of various lengths were tested, with the frequency of pressure waves varied for a fixed hose length, and pulsating flow was generated by a positive displacement pump. At certain hose lengths, outlet pressure pulsations were amplified while inlet pulsations were attenuated, demonstrating hydraulic resonance. The analysis was conducted using a four-piece hydraulic model, and experimental verification showed excellent agreement with the model predictions. Hose vibrations induced by the pulsating flow were also recorded. The results highlight critical hose lengths and excitation frequencies to avoid resonance, reducing vibrations and environmental impact. These findings provide guidance for designing precise, reliable hydraulic systems and serve as a basis for modeling more complex configurations.

Although cooling at ambient temperature is widely used and is said to be safe and convenient, faster cooling may have an influence not only on the time of the manufacturing process but also on the mechanical response, especially the residual stress. The study aimed to investigate the influence of the cooling rate after curing on the mechanical response of filament-wound thick-walled carbon fiber reinforced polymer (CFRP) rings. Three cooling rates were taking into consideration: cooling with the oven, at room temperature, and in the water at 20 °C. The splitting method was used to examine the residual strains. In the radial compression test, the mechanical response was investigated between the rings with different cooling regimes. The FEM analysis of the compression test in elastic range was also performed. Both the splitting method and the radial compression test showed no significant difference in the mechanical response of the CFRP rings. The presented results showed that the fast-cooling rate slightly decreases the mechanical performance of the filament-wound rings.

This paper presents a systematic literature survey on diagnostic methods used for railway materials and systems. The authors analyze various railway accident reports, focusing on the types of failures described and their causes. Previous review papers have addressed various aspects of railway...