Oxygen reduction reaction (ORR) has attracted considerable attention for clean energy conversion technologies to reduce traditional fossil fuel consumption and greenhouse gas emissions. Although platinum (Pt) metal is currently used as an electrocatalyst to accelerate sluggish ORR kinetics, the scarce resource and high cost still restrict its further scale-up applications. In this regard, biomass-derived carbon electrocatalysts have been widely adopted for ORR electrocatalysis in recent years owing to their tunable physical/chemical properties and cost-effective precursors. In this minireview, recent advances of the optimization strategies in biomass-derived carbon electrocatalysts towards ORR have been summarized, mainly focusing on the optimization of pore structure and active site. Besides, some current challenges and future perspectives of biomass-derived carbon as high-performance electrocatalysts for ORR have been also discussed in detail. Hopefully, this minireview will afford a guideline for better design of biomass-derived carbon electrocatalysts for ORR-related applications.
Perovskite materials have attracted extensive attention because of their superior performance in the fields of photoelectric detection, photovoltaics, light-emitting diodes, metal–air batteries, etc. However, their development and application in the field of X-ray detectors have not been reviewed. In this paper, research on perovskite-based X-ray detectors is analyzed using the bibliometric method. This analysis sample includes the literature from 1997 to the present. In addition, the research status of perovskite-based scintillators and direct X-ray detectors under different crystallization conditions and different preparation methods is discussed. Finally, several problems that need to be overcome in the future of perovskite-based X-ray detectors are put forward.
14 February 1994 in Journal of Physics D: Applied Physics
Certain organic crystals have attracted much attention owing to their nonlinear optical coefficients, at least one to two orders of magnitude above those of inorganic nonlinear optical materials. However, none of them has so far actually been applied in frequency conversion devices used with high-, medium- or low-power lasers. In this article the authors discuss the major factors affecting frequency conversion efficiency and examine characteristics of some frequently mentioned organic crystals. The properties and structure characterization of a new type of nonlinear optical crystal are also reported and discussed.
FeCuNbSiB and FeZrBCu nanocrystalline ribbons can be obtained directly through the melt- spinning technique without additional annealing processes. The giant magnetoimpedance can be observed in FeCuNbSiB and FeZrBCu as quenched ribbons. The addition of Cu improves the nano-crystallization of a-Fe(Si) or a-Fe phase and reduces the grain size in FeCuNbSiB and FeZrBCu as quenched ribbons, which enhances the magnetoimpedance via increasing the variation of permeability under fields. The present experimental results reveal a novel route to fabricate the Fe based nanocrystalline soft magnetic materials with giant magnetoimpedance effect.
Organic-inorganic hybrid perovskite solar cells (PSCs) have attracted considerable attention due to the excellent optoelectronic properties of perovskite materials. The energy consumption and high cost issues of metal electrode evaporation should be addressed before large-scale manufacturing and application. We developed an effective metal electrode evaporation procedure for the fabrication of high-efficiency planar heterojunction (PHJ) PSCs, with an inverted device structure of glass/indium tin oxide (ITO)/poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine] (PTAA)/perovskite/[6,6]-phenyl-C61-butyric acid methyl ester (PCBM)/(E)-β-caryophyllene (BCP)/Ag. The effect of the evaporation rate for an evaporator with a small-volume metal cavity on the performance of PHJ-PSC devices was investigated systematically. Through controlling the processes of Ag electrode evaporation, the charge dynamics of the devices were studied by analyzing their charge recombination resistance and lifetime, as well as their defect state density. Our findings reveal that the evaporation rate of an evaporator with a small cavity is favorable for the performance of PHJ-PSCs. As a result, PHJ-PSCs fabricated using a very thin, non-doped PTAA film exhibit photoelectric conversion efficiency (PCE) of 19.21%, with an open-circuit voltage (Voc) of 1.132 V. This work showcases the great potential of rapidly evaporating metal electrodes to reduce fabrication costs, which can help to improve the competitiveness in the process of industrialization.