This study addresses the role of metal spacer design in reducing the thermomechanical stress of solder joint in automotive double-sided cooling power electronics modules. The performance and reliability of power modules are becoming increasingly important in electrified vehicles. A double-sided cooling structure has dual heat sinks placed on the top and bottom of the module and is the most promising solution for improving the thermal reliability of power modules. One of unique components of this structure is its metal spacers, which are responsible for both electrical and thermal conductions via the connecting embedded power semiconductor dies and their top-side substrates. Reported spacers are typically cuboid in shape, providing a relatively large solder-contact area with the power dies. This large contact area is beneficial in reducing electrical and thermal resistance, but it increases thermomechanical stress and may accelerate the deterioration of die-bonded solders. This study explores the role of three new spacer shapes in reducing thermomechanical stress of the solder. Their performances are validated using both finite element method (FEM) simulations and thermal cycling experiments. In this study, an octagon-surface spacer demonstrates the best solder reliability compared to the two other designs and the conventional cuboid spacer.
7 July 2022 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This paper proposes a new estimation process of the actual maximum junction temperature in multi-chip SiC MOSFET power modules. Temperature-sensitive electrical parameters (TSEPs) are common methods to estimate the junction temperature of power devices, but they have limitations in specifying the actual maximum junction temperature in multi-chip power modules with anti-parallel diodes. Common TSEPs includes body-diode forward voltage or on-resistance of MOSFETs, but it is difficult to distinguish the impact of the anti-parallel diodes and the on-resistance-based method has low sensitivity under low-current calibration. Especially, the TSEPs has difficulty to calibrate the actual maximum junction temperature of a power module, which should solely detect the hottest device in the module. Therefore, a new dynamic calibration method is proposed using fiber optics while simultaneously monitoring factors related to the maximum junction temperature. Four critical parameters were measured from two different combinations: 4-paralleled and 10-paralleled SiC MOSFET power modules with anti-parallel diodes. Because of the abundant amount of the measured data, data-driven modeling was conducted with a deep neural network (DNN). The trained models were evaluated, demonstrating distinctly better accuracy in the actual maximum temperature estimation, for both 4-paralleled (MAE of 0.61 °C) and 10-paralleled (MAE of 0.72 °C) MOSFET modules.
27 November 2017 in IEEE Transactions on Industry Applications
Owing to the introduction of wide-bandgap power devices, recent power modules operate at higher temperatures. This increased module temperature leads to significant reliability problems, which render thermal monitoring very important. Several thermal sensors have been used in power modules; however, each of these sensors has drawbacks such as limited maximum temperature, nonlinearity, power source requirement, or limited miniaturization. This paper proposes a new temperature sensor that utilizes the piezoelectric effect. A new piezoelectric material (PZT-PZNM) with a high Curie temperature (260 °C) is soldered onto a direct bonded copper substrate. When the power module is operating at a high temperature, the substrate deflects and induces thermal stress, which is converted into an electric voltage via a piezoelectric mechanism. The voltage can be maximized by optimizing the location of the PZT-PZNM; the best location was determined to be away from the power devices. This observation confirms that the piezoelectric temperature sensor has a negligible influence on the performance of the power devices. Moreover, the sensor volume was miniaturized (approximately 74% reduction compared with preliminary work) to ensure that it can be readily integrated into power modules. The developed piezoelectric sensor demonstrates excellent linearity ( R 2 = 0.99, approximately) up to 250 °C, which is sufficient for monitoring temperature in both silicon and silicon carbide power modules.
In this paper, an approach to determine the thermal impedance of a multi-chip silicon carbide (SiC) power module is proposed, by fusing optical measurement and multi-physics simulations. The tested power module consists of four parallel SiC metal-oxide semiconductor field-effect transistors (MOSFETs) and four parallel SiC Schottky barrier diodes. This study mainly relies on junction temperature measurements performed using fiber optic temperature sensors instead of temperature-sensitive electrical parameters (TESPs). However, the fiber optics provide a relatively slow response compared to other available TSEP measurement methods and cannot detect fast responses. Therefore, the region corresponding to undetected signals is estimated via multi-physics simulations of the power module. This method provides a compensated cooling curve. We analyze the thermal resistance using network identification by deconvolution (NID). The estimated thermal resistance is compared to that obtained via a conventional method, and the difference is 3.8%. The proposed fusion method is accurate and reliable and does not require additional circuits or calibrations.
21 October 2019 in IEEE Transactions on Vehicular Technology
This study presents designs, multi-physics finite element method (FEM) and circuit simulations, and experimental validations of a three-phase inverter power module for an electric compressor (e-Compressor) used in 48V mild hybrid vehicles. The inverter module is integrated with its motor and scroll. The integration and e-Compressor operation situations raise sequential challenges in the module design and analysis. Thus, the e-Compressor module employs a direct bonded copper (DBC) substrate on which MOSFET dies, shunt resistors, and other electronics are soldered. Multi-physics FEM and circuit simulations are conducted to analyze (and minimize) parasitic and loop inductances, current concentration, and the temperature elevation of the design. Modeling and simulation processes are customized to represent the integrated DBC-based e-Compressor module, including the determination of loop inductance and overshoot voltage by considering systemic current conduction, and reasonable simplification of cooling fluid effects. The simulation process and module performances are validated by experiments. The designed e-Compressor inverter module is improved to fully satisfy all the required specifications. Moreover, an excellent agreement between the simulation and the experimental results is confirmed, demonstrating the similar reductions of (1) loop inductances simulated by FEM (~57%), (2) circuit-simulated overshoot voltages (~47%), and (3) experimentally measured overshoot voltages (~53%).