Accurate and real-time acquisition of vehicle state parameters is key to improving the performance of vehicle control systems. To improve the accuracy of state parameter estimation for distributed drive electric vehicles, an unscented Kalman filter (UKF) algorithm combined with the Huber method is proposed. In this paper, we introduce the nonlinear modified Dugoff tire model, build a nonlinear three-degrees-of-freedom time-varying parametric vehicle dynamics model, and extend the vehicle mass, the height of the center of gravity, and the yaw moment of inertia, which are significantly influenced by the driving state, into the vehicle state vector. The vehicle state parameter observer was designed using an unscented Kalman filter framework. The Huber cost function was introduced to correct the measured noise and state covariance in real-time to improve the robustness of the observer. The simulation verification of a double-lane change and straight-line driving conditions at constant speed was carried out using the Simulink/Carsim platform. The results show that observation using the Huber-based robust unscented Kalman filter (HRUKF) more realistically reflects the vehicle state in real-time, effectively suppresses the influence of abnormal error and noise, and obtains high observation accuracy.

For vehicle state estimation, conventional Kalman filters work well under Gaussian assumptions. Still, they are likely to degrade dramatically in the practical non-Gaussian situation (especially the noise is heavy-tailed), showing poor accuracy and robustness. This article presents an estimation technique based on the maximum correntropy criterion (MCC) combined with an adaptive extended Kalman filter (AEKF), and an extended Kalman filter (EKF) based on the MCC has also been studied. A lateral-longitudinal coupled vehicle model is developed, while an observer containing the state vectors such as yaw rate, sideslip angle, vehicle velocity and tire cornering stiffness is designed using easily available in-vehicle sensors and low-cost GPS. After analyzing the algorithmic complexity, the proposed algorithm is validated by sine steering input and double lane change driving scenarios. Finally, it is found that MCC combined with AEKF/EKF has stronger robustness and better estimation accuracy than AEKF/EKF in dealing with non-Gaussian noise for vehicle state estimation.

The distributed drive arrangement form has better potential for cooperative control of dynamics, but this drive arrangement form increases the parameter acquisition workload of the control system and increases the difficulty of vehicle control accordingly. In order to observe the vehicle motion state accurately and in real-time, while reducing the effect of uncertainty in noise statistical information, the vehicle state observer is designed based on interacting multiple model theory with square root cubature Kalman filter (IMM-SCKF). The IMM-SCKF algorithm sub-model considers different state noise and measurement noise, and the introduction of the square root filter reduces the complexity of the algorithm while ensuring accuracy and real-time performance. To estimate the vehicle longitudinal, lateral, and yaw motion states, the algorithm uses a three degree of freedom (3-DOF) vehicle dynamics model and a nonlinear brush tire model, which is then validated in a Carsim-Simulink co-simulation platform for multiple operating conditions. The results show that the IMM-SCKF algorithm’s fusion output results can effectively follow the sub-model with smaller output errors, and that the IMM-SCKF algorithm’s results are superior to the traditional SCKF algorithm’s results.

Accurate acquisition of vehicle dynamics state information is essential for vehicle active safety control systems. However, these states cannot be easily measured, and the measurement is expensive. Conventional Kalman filters perform well for vehicle state estimation in Gaussian environments but exhibit low accuracy and robustness under practical non-Gaussian noise. Vehicle model parameter ingestion, inaccurate tire force calculation, and non-Gaussian noise from on-board sensors cause great challenges to the estimation of vehicle driving states. Therefore, this paper presents a robust hierarchical estimation scheme for vehicle driving state based on the maximum correntropy square-root cubature Kalman filter (MCSCKF) using easily measurable on-board sensor information. First, the vehicle mass is dynamically updated based on the recursive least squares (FRLS) method with a forgetting factor. Then, an adaptive sliding mode observer (ASMO) is designed to estimate the longitudinal and lateral tire forces. Ultimately, the vehicle states are estimated based on the MCSCKF under non-Gaussian noise. Two typical operating situations are carried out to verify the validity of the proposed estimation scheme. The results prove that the proposed estimation scheme can estimate the vehicle’s driving state accurately compared to other common methods. And the MCSCKF algorithm has better accuracy and robustness than the traditional Kalman filters for vehicle state estimation in non-Gaussian situations.