This paper investigates the potential energetic utilization of wheat chaff via combustion and necessary process steps such as pretreatment and pellet production as an example of stramineous biomass. Chaff is one out of three main fractions during harvesting and remains usually on the field. Vice versa, it is a potentially so far unexploited biomass resource, which could serve as renewable energy source. Simultaneously, exploiting wheat chaff could intensify the economic benefit of agricultural land use. The combustion application requires choosing an applicable firing system adjusted to the properties of chaff. The economic feasibility of the combustion application depends strongly on the technical effort, which depends on the fuel. Chaff consists mainly of husks and straw. Due to the low ash melting point and the high chlorine content of straw, it can be advantageous for the combustion to remove short straw from the chaff by sieving. To evaluate the combustion properties of presorted and original chaff the elemental composition, the net calorific value, the volatiles and ash content and the ash melting behavior were determined. The efficient logistic of chaff is decisive for its economic exploitation. This is in conflict with the low bulk density of chaff and the resulting high storage volume. Compressing chaff into pellets optimizes its handling. This vital step for an economic exploitation of chaff was therefore investigated by this study. Parameters such as water content of the feed, addition of binders and the geometry of the pressing die bores influence the pelletizing success significantly. Thus these parameters were investigated in this study. The resulting pellets were characterized with standardized methods and compared to the requirements of EnPlus standards in terms of mechanical durability, amount of fines, bulk density and final moisture content. Finally, combustion experiments in a Large-scale Oven for Kinetics Investigation characterized the burnout behavior of the produced pellets. This was compared to pine wood pellets as conventional fuel. The performed investigations show that the pellet production and the subsequent combustion of wheat chaff pellets is a feasible approach for an energetic utilization.
This review studies unwanted precipitation reactions, which can occur in SO2 absorption processes using a magnesium hydroxide slurry. Solubility data of potential salts in the MgO-CaO-SO2-H2O system are evaluated. The reviewed data can serve as a reliable basis for process modeling of this system used to support the optimization of the SO2 absorption process. This study includes the solubility data of MgSO3, MgSO4, Mg(OH)2, CaSO3, CaSO4, and Ca(OH)2 as potential salts. The solubility is strongly dependent on the state of the precipitated salts. Therefore, this review includes studies on the stability of different forms of the salts under different conditions. The solubility data in water over temperature serve as a base for modeling the precipitation in such system. Furthermore, influencing factors such as pH value, SO2 content and the co-existence of other salts are included and available data on such dependencies are reviewed. Literature data evaluated by the International Union of Pure and Applied Chemistry (IUPAC) are revisited and additional and newer studies are supplemented to obtain a solid base of accurate experimental values. For temperatures higher than 100 °C the available data are scarce. For a temperature range from 0 to 100 °C, the reviewed investigations and data provide a good base to evaluate and adapt process models for processes in order to map precipitations issues accurately.
2 August 2023 in Industrial & Engineering Chemistry Research
Red liquor combustion is a crucial step in the chemical recovery process in the pulp and paper industry and has two main functions: recovering MgO and SO2 from magnesium bisulfite spent liquor and generating steam as a heat source for further usage. This research aims to analyze how different red liquor spraying characteristics affect combustion time, guiding recommendations for optimal spraying characteristics to achieve faster combustion using computational fluid dynamics (CFD). Red liquor combustion is simulated in the open-source environment OpenFOAM®, employing Eulerian–Lagrangian coupling simulations, treating red liquor droplets as Lagrangian particles. One-step devolatilization and combustion kinetics are derived from performed non-isothermal thermogravimetric analyses (TGA) and implemented into the model. An industrial red liquor combustion vessel served as a reference case. Through virtual experiments, we explore the impact of spray angle (15° and 30°), droplet size (2 mm and 3 mm), and spray type (fullcone vs. hollowcone) on combustion time. The performed simulations indicate that the combustion time can be reduced by approximately 30% by reducing the characteristic particle diameter from 3 mm to 2 mm. Furthermore, hollowcone spraying revealed faster combustion times than fullcone spraying. The fastest combustion time was achieved with a characteristic particle size of 2 mm, a spraying angle of 30°, and using a hollowcone spray type.