Reducing non-revenue water (NRW) within a water distribution network may lead to significant water savings. Most existing literature tend to focus on the design and implementation aspects of NRW loss through better management of leaks, reservoir overflow, and water theft. In contrast, this paper examines the association between the various water pipe types and their respective impact on NRW loss in an emerging country. Malaysia is currently listed under emerging and developing economies category in the International Monetary Fund World Economic Outlook Database (October 2020). A correlation analysis is carried out using historical data obtained from the Malaysian water authority, covering fiscal years 2013 to 2017 (inclusive of both years). Further analysis is carried out by measuring the number of cases reported for two selected states in relation to the type of pipe materials used. Results show that there is a significant correlation between mild steel and polyethylene pipes to NRW loss. This study provides a better understanding of how water pipe types affect NRW loss, which is pertinent to developing best practices in the marketplace to manage NRW loss and protect water resources.
This paper presents a pioneering effort to ascertain the suitability of hyperelastic modelling in simulating the stress–strain response of oil palm shell reinforced rubber (ROPS) composites. ROPS composites with different oil palm shell contents (0%, 5%, 10% and 20% by volume) were cast in the laboratory for the experimental investigation. ROPS specimens with circular, square, hexagon, and octagon shapes (loading surface) were considered to evaluate the accuracy of finite element simulation considering the shape effect of composites. Strain-controlled (compressive) tests with ε ≈ 50% at 0.8 Hz frequency were conducted in the laboratory and the test data obtained was used as input to simulate material coefficients corresponding to the strain energy functions chosen. Five different strain energy functions were selected and utilized for the hyperelastic modelling in this study using finite element approach. The shape effect was then used to ascertain any variation in the simulation outcomes and to discuss the effect of shape on the behaviour of ROPS composites in comparison to existing literature. The numerical predictions using the Yeoh model (error ≤ 2.7% for circular shaped ROPS) were found to perform best in comparison with the experimental results, thus a more stable and suitable hyperelastic model to this end. The Marlow (error ≤ 4.6% for circular shaped ROPS) and Arruda Boyce (error ≤ 4.7% for circular shaped ROPS) models were amongst the next alternatives to perform better. Even with the other shapes considered in this study, Yeoh, followed by the Marlow function, were more appropriate models. The shape effect was then studied with particular emphasis on comparing and assessing them with that observed in the literature. To this end, adopting the Yeoh function in the finite element model is the ideal approach to estimate the stress–strain response of ROPS composites.
Background: Porous silicon (pSi) nanoparticles (NPs) functionalized with suitable targeting ligands are now established cancer bioimaging agents and drug-delivery platforms. With growing interest i... Graphical abstract Two types of legumain-targeting peptide (linear and Y-branched) functionalized porous silicon (pSi) nanoparticles were successfully synthesized. The targeting specificity of the ...
1 July 2016 in International Journal of Aviation, Aeronautics, and Aerospace
The effect of interactions of vortices produced by an outboard flap-tip of a half-span wing (NACA 23012 in landing configuration) and a slender reverse delta type add-on device, placed in the proximity of the outboard flap-tip, on the upper surface of the half-span wing is investigated using Particle Image Velocimetry in a closed loop low speed wind tunnel. Specifically the characteristics of the vortex interactions generated downstream in planes perpendicular to the free stream direction and their dependence on angles of attack at a chord-based Reynolds number of Rec=2.75×105 have been determined. It was found that the add-on device significantly reduces the tangential velocity magnitude and enlarges the vortex core of the resultant vortex by up to 36%. The aerodynamic performance of the half-span wing model was marginally affected by the use of a reverse delta type add-on device. The reduction in lift coefficient is 3.8% and the increase in drag coefficient is 14.9%.
2 April 2023 in International Journal of Pavement Engineering
This study focuses on evaluating the response of concrete block pavement (CBP) reinforced with rubberised oil palm shell (ROPS) layers when subjected to vehicular loads using laboratory experiments and finite element (FE) simulations. The key parameters considered in this study are the sand bed thickness, oil palm content in ROPS layers, embedment depth of ROPS layers, and vehicle velocity. The dynamic loads due to the vehicular movement were generated using a real-time road unevenness signal. Outcomes from the lab-scale 1g experiments and FE simulations were expressed as displacement and acceleration responses in the frequency domain. CBP sections with sand bed thicknesses of 10mm and 70mm were found to yield high surface deflection and acceleration values, both with and without ROPS reinforcements. CBPs reinforced with the ROPS layer having 20% OPS content demonstrate the best performance compared to ROPS layers made with 5% and 10% OPS contents. Further simulations show that the ROPS layers at an optimum embedment depth of 180mm from the surface in the CBP profile can significantly reduce the unacceptable levels of vibration. To this end, this preliminary research attempts the possible reengineering of oil palm shells and ascertains the suitability of ROPS reinforcements in stabilising CBP−soil systems.
1 March 2017 in IOP Conference Series: Materials Science and Engineering
Particle Image Velocimetry was used in a low speed wind tunnel to investigate the effect of interactions of vortices produced by an outboard flap-tip of a half wing (NACA 23012 in landing configuration) and a slender reverse delta type add-on device, placed in the proximity of the outboard flap-tip, on the upper surface of the half wing. This work investigates the characteristics of the vortex interactions generated downstream in planes perpendicular to the free stream direction at a chord-based Reynolds number of Rec=2.74×105. It was found that the add-on device significantly reduces the tangential velocity magnitude and enlarges the vortex core of the resultant vortex by up to 36.1% and 36.8%, respectively.