Phase change materials (PCMs) are now widely known as potential additives for building insulation materials to provide a thermal mass effect that helps conserve energy and maintain a comfortable indoor temperature. Therefore, the study presented in this paper focuses on an experimental investigation of the specific heat capacity and thermal conductivity of hemp shive mixed with PCMs. Industrially manufactured organic PCM-S50 received from MikroCaps Ltd. (Slovenia) has been used to further enhance respective properties of the product samples. The experimental boards were made from hemp shive by directly mixing 5% encapsulate PCMs into the mass. Cold pressing was used to manufacture the boards with Kleiberit urea formaldehyde resin glue as a binding agent. The experimental boards were made as 25 mm thick single-layer parts with a density of 300 ± 20 kg/m³, which qualify them as low-density boards. By adding nanocapsules during the board manufacturing process, the heat capacity is increased by 62%. Based on the great potential of using latent heat, it becomes a possible solution for the development of new technologies related to the automatic regulation of an indoor microclimate.

Over the past few decades, climate change and the search for renewable energy sources have become hot topics within the research community. About 30% of the world's energy consumption is in the heating and cooling sector of residential buildings. Such materials can reduce the temperature variations, leading to an improvement in human comfort and decreasing at the same time the energy consumption of buildings. This paper assesses the integration of a microencapsulated phase change material (PCMs) with organic composite phase change as the core material and melamine-formaldehyde as the shell in hemp shive intended for building indoor wallboard. Paraffin waxes are cost-effective and have moderate thermal energy storage density but low thermal conductivity and, hence, require large surface area. Commercial manufactured organic PCM-S28 with a 25-29°C melting point received from MikroCaps Ltd. (Slovenia) has been used. The experimental boards were made using cold pressing technology and with 10% Kleiberit Urea Formaldehyde resin (UF) glue as a binding agent. The experimental boards were made 25 mm thick with a density of 310 ± 20 kg/m3 that qualify them as low-density boards. By adding 5% nanocapsules during the board manufacturing process, the heat capacity is increased by 28%.

In this research, agricultural residue of seed hemp variety “Adzelvieši” was used to create hemp particleboard samples. Hemp was grown in three experimental fields where it was observed that after seed harvesting, 3.5 tonnes of hemp stems per hectare remained. The plants were processed with milling, cutting, and sieving equipment. Moisture content and particle size distribution were observed throughout raw material processing. Hemp boards were produced using the cold pressing method with 10% urea formaldehyde resin as the binder. The boards were made as 20 mm thick single-layer parts with a density range of 220 ± 30 kg/m³ and porosity of 86%. Board structural analysis was performed using optical microscopy and scanning electron microscopy methods. Mechanical strength was determined by performing bending strength, internal bond strength, and screw withdrawal tests. The thermal conductivity reached 0.047 ± 0.008 W/(mK). The results were compared with industrially produced hemp shive boards and materials in the developmental or production stage. The feasibility for the experimental production cycle proposed in the study is discussed.

The growing availability and decreasing cost of microencapsulated phase change materials (PCMs) present an opportunity to develop innovative insulation materials for latent heat energy storage. By integrating PCMs with traditional insulation materials, it is possible to enhance the thermal capacity of a building by up to 2.5-times, virtually without increasing the building’s mass. To improve buildings’ indoor structural performance, as well as improving their energy performance, microencapsulated PCMs are integrated into wallboards. The integration of microencapsulated PCMs into the wallboard solves the PCM leakage problem and assures a good bond with the building materials to achieve better structural performance. The novelty of this research is the application of encapsulated phase change material dispersion and technology for its incorporation into the structure of hemp shives and longitudinally milled wood chip-based insulation boards, using cold pressing technology to reduce the energy consumption of board production. As a result, low-density insulation boards for indoor application were produced by varying their structure and the amount of phase change materials in the range of 5% to 15% by board mass. The obtained board prototypes can be used as microclimate and thermoregulation elements of interiors, as well as functional aesthetic elements of interior design.

Purpose: Based on profound information lacking in compiled information materials, the risks of losing knowledge related to the values of traditional woodworking processes are increasing. The purpose of this article is to collect and structure diverse marking tool data into a comprehensive, understandable and clear design schematic view, which serves as a basis for the accumulation and preservation of diverse marking objects and shows woodworking marking tool relation in the group and subgroup levels.Design/methodology/approach: A method for marking tools structuring and analysis are described, including breaking down a set of objects into groups of marking objects, and assigning one or more attributes to the parcelled objects by arranging them into hierarchic levels. Research is based on marking tools used by carpenters, joiners and woodcarvers mainly in the Baltic region.Findings: Collected data, object analyses and comparison within-group and subgroup levels are based on written and visual sources, museum and museum funds visits, and participation in the local craftsmen events. The created structure is expandable in group and subgroup levels. The most comprehensive way for object structuring is chosen as a base to reveal a diversity of the objects.Originality/value: Structure schemes of woodworking marking tools are important in scientific, educative and cultural levels based on their wide range and use. Aggregated information of the woodworking tools serves as a base for existing tool studies and improvement, new tool and wood product creation as well as complements the structure of the upcoming woodworking hand tool database and book.

The technology makes it possible to obtain insulation materials for indoor spaces with 2.5 times higher performance from agricultural and wood processing by-products and PCM.