Aging by 10,000 thermal cycles significantly decreases the repair bond strength of composite and surface preparation by bur provides a higher bond strength compared to laser. Thermocycling, Composite, Repair, Laser.
Objective Lifelike esthetic appearance of dental restorations is among the main goals in restorative dentistry. This study aimed to assess and compare the opalescence and fluorescence of two dental composite resins. Materials and Methods This in vitro experimental study evaluated the A2 shade of Filtek Z350 XT Enamel, Filtek Z350 XT Dentin, Aelite Aesthetic Enamel, and Aelite All Purpose Body composite resins. Composite discs were fabricated with 10 mm diameter and 0.5 and 1 mm thicknesses (n = 2) using a plexiglass mold and subjected to colorimetry. The color parameters were determined according to the International Commission on Illumination (CIE) L*a*b* system using a spectrophotometer. The fluorescence and opalescence were also measured and reported separately for 0.5 and 1 mm thicknesses of Z350, Aelite Body, and Enamel composite resins. To determine the opalescence, the color of samples in the reflectance mode was measured using a calibration cylinder and in the transmittance mode in presence of 100% ultraviolet (UV) light. To determine the fluorescence, the color of samples against a white background in the reflectance mode in presence or absence of 100% UV light was measured. Statistical Analysis Data were analyzed using SPSS via three-way analysis of variance and independent t-test. Results The fluorescence of 0.5 mm thickness of all composites was higher than that of 1 mm thickness (p < 0.05). The fluorescence of Aelite was higher than that of Z350 (p < 0.05). The fluorescence of Aelite Enamel was higher than that of Aelite Body irrespective of their thickness, but the results were opposite for Z350 (p < 0.05). In Aelite composite, opalescence increased by an increase in thickness (p < 0.05). The opalescence of Aelite was significantly higher than that of Z350 (p < 0.05). The opalescence of 0.5 mm thickness of Aelite Enamel was higher than that of Aelite Body, while the opalescence of 1 mm thickness of Z350 Body was higher than that of Z350 Enamel (p < 0.05). Conclusion Thickness, type, and brand of composite resins affected their fluorescence and opalescence.
Objectives: This study aimed to assess the effect of surface treatment by bur and laser and application of universal adhesive on repair bond strength of composite resin. Materials and Methods: A total of 120 composite blocks measuring 6x4x4 mm were fabricated of Filtek Z250 composite. All samples were subjected to 5,000 thermal cycles and divided into two groups for surface preparation by bur and by Er,Cr:YSGG laser (n = 60). The surfaces were then etched with orthophosphoric acid, rinsed with water and divided into three groups (silane, silane plus Single Bond and silane plus Single Bond Universal). Repair composite was then bonded to aged composite. Half of the samples in each group were stored in distilled water at 37°C for 24 hours and the other half underwent 5000 thermal cycles. All samples were then subjected to shear bond strength testing using a universal testing machine at a crosshead speed of 1 mm/minute. The data were analyzed using one-way ANOVA and Tukey’s HSD test. Mode of failure was determined using a stereomicroscope. Results: Bur preparation plus universal adhesive yielded the highest bond strength (30.16 ± 2.26 MPa). Laser plus silane yielded the lowest bond strength (5.63 ± 2.43 MPa). Bur preparation yielded significantly higher bond strength than laser (P < 0.001). Also, application of universal adhesive significantly improved bond strength compared to conventional adhesive and silane (P < 0.001). Bond strength after aging (5000 thermal cycles) had no significant difference with primary bond strength at 24 hours within each group (P = 0.182). Conclusion:Surface preparation of aged composite by bur and application of universal adhesive can improve the repair bond strength of composite. Application of silane (without adhesive) in the process of repair cannot provide adequately high repair bond strength.
Introduction: This study sought to assess the effect of bleaching combined with irradiation of 810 nm and 980 nm diode laser on microhardness of 2 commonly used self-cure and light-cure glass ionomer cements (GICs) in comparison with conventional bleaching (without laser). Methods: In this in vitro, experimental study, 60 samples were fabricated of A2 shade of Fuji IX and Fuji II LC GICs (n=30) and each group was divided into 3 subgroups (n=10). The first subgroups were subjected to bleaching with Opalescence Xtra Boost plus 980 nm diode laser irradiation. The second subgroups were subjected to bleaching with Opalescence Boost plus 810 nm diode laser irradiation and the third subgroups were subjected to bleaching with Opalescence Xtra Boost without laser. Microhardness was measured at baseline and after the intervention using Vickers hardness tester. The data were analyzed using two-way analysis of variance (ANOVA) (P<0.05). Results: Microhardness decreased in all subgroups after the intervention (P<0.001) irrespective of the type of GIC (P=0.201) or surface treatment (P=0.570). The baseline microhardness of the three subgroups within each group of GIC was not significantly different (P=0.456), but the baseline microhardness of conventional GIC was significantly higher than that of resin modified GIC (P=0.004). Conclusion: Bleaching with/without laser irradiation decreases the microhardness of GICs. The baseline microhardness of conventional GIC is higher than that of resin modified GIC.
The surface microhardness of dental composites greatly affects the durability of restorations. The aim of this study was to compare the surface microhardness of a self-adhesive composite with that of other conventional composites. The effect aging has on surface microhardness was also evaluated. In this in vitro experimental study, the composite resins were poured into molds measuring 3 mm × 3 mm × 6 mm and cured for 40 s. The samples were then immersed in distilled water at 37°C for 24 h. After polishing, the surface microhardness of the samples was measured using the Vickers hardness tester. For this purpose, a 100-gram load was applied to 3 points on the surface of each composite sample for 20 s, and the mean value of surface microhardness was used as the Vickers hardness number. The samples were then subjected to 30,000 thermal cycles at 5-55°C in order to age them; after that, their surface microhardness was measured again. The one-way analysis of variance (ANOVA) was used for the statistical analysis. The maximum hardness value before and after aging belonged to Filtek® Z250, followed by Premise™ Flow and Vertise™ Flow, with significant differences between them (p < 0.001). After aging, the surface microhardness of all composites decreased significantly (p < 0.001). The effect of aging on surface microhardness was the same in all groups (p > 0.05). The surface microhardness of composites was significantly different before and after aging. All composites experienced a reduction in their surface microhardness after aging.