Adhesion state is a key factor affecting the motion stability of a wall-climbing robot. According to different adhesion states, there is no universal method for compliant detachment. We propose an online impedance strategy for controlling peeling angle to realize compliant movement. Variable compliant motions are achieved by online tuning the stiffness and damping parameters of proportional-derivative control, which realizes compliant detachment with a peeling angle of , the adhesion strength to adjust to a minimum and basically eliminated the instant change in normal adhesion strength at the detachment end state. The proposed controller was validated using a vertical climbing robot. The results showed that, with the proposed controller, the sudden change in the normal adhesion force during peeling was significantly reduced. Besides, there is no correlation between the sudden change in the normal adhesion force at the detachment end state and the adhesion state. Regardless of the adhesion states, the compliant detachment can be accomplished reliably.
To increase the knowledge and exploit new resources beyond the Earth, planetary surface exploration on the Moon or Mars attracts significant attention around the globe. Due to the fact that these planetary surfaces are widely covered by soil-like materials, various structures of planetary rovers have been proposed to adapt to the terrains. Nonetheless, the traditional rover structures, such as wheeled and leg-wheeled, have shown limitations in moving on granular soils. To improve the mobility, this paper proposes a multi-toe quadruped robot inspired by the desert chameleon animal. The key features are that each bionic foot possesses four toes to stabilize them on granular materials. Moreover, a bionic flexible spine is designed to coordinate with walking and turning gaits and to make the robot approach an animal-like mobility. To assess the robot performances, kinematics analysis and analytical modeling of foot, leg, and spine movements are carried out. The results demonstrate that this robot can effectively walk and turn in accordance with the adopted gaits. Finally, field tests of moving over sands have been conducted. It shows that the robot can stably walk and turn on sands, which indicates that it is adaptable to planetary granular terrains.
The agile locomotion of adhesive animals is mainly attributed to their sophisticated hierarchical feet and reversible adhesion motility. Their structure–function relationship is an urgent issue to be solved to understand biologic adhesive systems and the design of bionic applications. In this study, the reversible adhesion/release behavior and structural properties of gecko toes were investigated, and a hierarchical adhesive bionic toe (bio-toe) consisting of an upper elastic actuator as the supporting/driving layer and lower bionic lamellae (bio-lamellae) as the adhesive layer was designed, which can adhere to and release from targets reversibly when driven by bi-directional pressure. A mathematical model of the nonlinear deformation and a finite element model of the adhesive contact of the bio-toe were developed. Meanwhile, combined with experimental tests, the effects of the structure and actuation on the adhesive behavior and mechanical properties of the bio-toe were investigated. The research found that (1) the bending curvature of the bio-toe, which is approximately linear with pressure, enables the bio-toe to adapt to a wide range of objects controllably; (2) the tabular bio-lamella could achieve a contact rate of 60% with a low squeeze contact of less than 0.5 N despite a ±10° tilt in contact posture; (3) the upward bending of the bio-toe under negative pressure provided sufficient rebounding force for a 100% success rate of release; (4) the ratio of shear adhesion force to preload of the bio-toe with tabular bio-lamellae reaches approximately 12, which is higher than that of most existing adhesion units and frictional gripping units. The bio-toe shows good adaptability, load capacity, and reversibility of adhesion when applied as the basic adhesive unit in a robot gripper and wall-climbing robot. Finally, the proposed reversible adhesive bio-toe with a hierarchical structure has great potential for application in space, defense, industry, and daily life.
Hyper-redundant manipulators with multiple degrees of freedom have special application prospects in narrow spaces, such as detection in small spaces in aerospace, rescue on-site disaster relief, etc. In order to solve the problems of complex obstacle avoidance planning and inverse solution selection of a hyper-redundant robot in a narrow space, a cubic B-spline curve based on collision-free trajectory using environmental edge information is planned. Firstly, a hyper-redundant robot composed of four pairs of double UCR (Universal-Cylindrical-Revolute) parallel mechanisms (2R1T, 2 Rotational DOFs and 1 Translation DOF) in series to realize flexible obstacle avoidance motion in narrow space is designed. The trajectory point envelope of a single UCR and the workspace of a single pair of UCR in Cartesian space based on the motion constraint boundaries of each joint are obtained. Then, the constraint control points according to the edge information of the obstacle are obtained, and the obstacle avoidance trajectory in the constrained space is planned by combining the A* algorithm and cubic B-spline algorithm. Finally, a variety of test scenarios are built to verify the obstacle avoidance planning algorithm. The results show that the proposed algorithm reduces the computational complexity of the obstacle avoidance process and enables the robot to complete flexible obstacle avoidance movement in the complex narrow space.
Gravitational forces can induce deviations in body posture from desired configurations in multi-legged arboreal robot locomotion with low leg stiffness, affecting the contact angle between the swing leg’s end-effector and the climbing surface during the gait cycle. The relationship between desired and actual foot positions is investigated here in a leg-stiffness-enhanced model under external forces, focusing on the challenge of unreliable end-effector attachment on climbing surfaces in such robots. Inspired by the difference in ceiling attachment postures of dead and living geckos, feedforward compensation of the stance phase legs is the key to solving this problem. A feedforward gravity compensation (FGC) strategy, complemented by leg coordination, is proposed to correct gravity-influenced body posture and improve adhesion stability by reducing body inclination. The efficacy of this strategy is validated using a quadrupedal climbing robot, EF-I, as the experimental platform. Experimental validation on an inverted surface (ceiling walking) highlights the benefits of the FGC strategy, demonstrating its role in enhancing stability and ensuring reliable end-effector attachment without external assistance. In the experiment, robots without FGC only completed 3 out of 10 trials, while robots with FGC achieved a 100% success rate in the same trials. The speed was substantially greater with FGC, achieving 9.2 mm s−1 in the trot gait. This underscores the proposed potential of the FGC strategy in overcoming the challenges associated with inconsistent end-effector attachment in robots with low leg stiffness, thereby facilitating stable locomotion even at an inverted body attitude.
Animals have evolved highly effective locomotion capabilities in terrestrial, aerial, and aquatic environments. Over life’s history, mass extinctions have wiped out unique animal species with specialized adaptations, leaving paleontologists to reconstruct their locomotion through fossil analysis. Despite advancements, little is known about how extinct megafauna, such as the Ichthyosauria one of the most successful lineages of marine reptiles, utilized their varied morphologies for swimming. Traditional robotics struggle to mimic extinct locomotion effectively, but the emerging soft robotics field offers a promising alternative to overcome this challenge. This paper aims to bridge this gap by studying Mixosaurus locomotion with soft robotics, combining material modeling and biomechanics in physical experimental validation. Combining a soft body with soft pneumatic actuators, the soft robotic platform described in this study investigates the correlation between asymmetrical fins and buoyancy by recreating the pitch torque generated by extinct swimming animals. We performed a comparative analysis of thrust and torque generated by Carthorhyncus, Utatsusaurus, Mixosaurus, Guizhouichthyosaurus, and Ophthalmosaurus tail fins in a flow tank. Experimental results suggest that the pitch torque on the torso generated by hypocercal fin shapes such as found in model systems of Guizhouichthyosaurus, Mixosaurus and Utatsusaurus produce distinct ventral body pitch effects able to mitigate the animal’s non-neutral buoyancy. This body pitch control effect is particularly pronounced in Guizhouichthyosaurus, which results suggest would have been able to generate high ventral pitch torque on the torso to compensate for its positive buoyancy. By contrast, homocercal fin shapes may not have been conducive for such buoyancy compensation, leaving torso pitch control to pectoral fins, for example. Across the range of the actuation frequencies of the caudal fins tested, resulted in oscillatory modes arising, which in turn can affect the for-aft thrust generated.