This study applied oxygen-enrichment conditions to remove tar (the main problem in biomass gasification) and increase gasification efficiency. Experiments on oxygen-enrichment conditions were conducted at oxygen concentrations of 21%, 25%, 30%, and 35% in oxidants. This was expected to increase the partial oxidation reaction in gasification reactions, thus leading to thermal decomposition of tar in producer gas. The decomposed tar was expected to be converted into syngas or combustible gases in the producer gas. The results were as follows: Tar-reduction efficiency was 72.46% at 30% oxygen enrichment compared to the standard 21% enrichment condition. In addition, the concentrations of syngas and combustible gases in the producer gas tended to increase. Therefore, the 30% oxygen-enrichment condition was optimal, resulting in 78.00% for cold gas efficiency and 80.24% for carbon conversion efficiency. The application of oxygen enrichment into the lab-scale gasification system clearly reduced the concentration of tar and tended to increase some indexes of gasification efficiency, thus suggesting the usefulness of this technique in large-scale biomass gasification operations.

Thirteen types of fuel pellets were prepared from hydrothermally treated hospital solid waste, hydrothermally treated rice straw, pyrolytic plastic waste residue, rice straw, and Sakhalin fir residue using a flat die pellet machine. Different pellet properties such as pellet density, pellet durability, aspect ratio, physicochemical characteristics, and gross calorific value (GCV) were evaluated as well as compared concerning the European standard specification for residential/commercial densified fuels. In addition, the quality of pellets was compared with coal. The results showed that the pellets made only with hydrothermally treated hospital solid waste, hydrothermally treated rice straw, pyrolytic plastic waste residue, and rice straw failed to meet few individual criteria (<3 wt% ash content, <10 wt% moisture content, 96.5 wt% pellet durability, and >600 kg/m³ pellet density) of the European standard specifications. However, most of the mixed fuel pellets satisfied the requirement of pellet properties according to the European standard specification. In particular, up to 16.70 wt% hydrothermally treated rice straw, 1.50 wt% hydrothermally treated hospital solid waste, and 4.76 wt% of pyrolytic plastic waste residue can be blended with Shakhalin fir residue to produce low-chlorine fuel pellets. The gross calorific value of pellets made from the mixture of hydrothermally treated wastes and pyrolytic plastic waste residue (around 22 MJ/kg) showed similar results to that of coal. In the case of mixed pellets, the presence of these hydrothermally treated wastes and pyrolytic plastic waste residue valorized the fuel pellet quality. The main outcome of this study was the production of low chlorine biomass fuel pellets of high gross calorific values blended with hydrothermally treated wastes and pyrolytic waste residues, which opens a new door for utilizing waste in a better way, especially hospital solid waste.

Gaining energy independence by utilizing new and renewable energy resources has become imperative for Korea. Energy recovery from Korean municipal solid waste (MSW) could be a promising option to resolve the issue, as Korean MSW is highly recyclable due to its systematic separation, collection and volume-based waste disposal system. In this study, gasification experiments were conducted on Korean municipal waste-derived solid fuel (SRF) using a fixed bed reactor by varying the equivalence ratio (ER) to assess the viability of syngas production. Experiments were also conducted on coal and biomass under similar conditions to compare the experimental results, as the gasification applicability of coal and biomass are long-established. Experimental results showed that Korean SRF could be used to recover energy in form of syngas. In particular, 50.94% cold gas efficiency and 54.66% carbon conversion ratio with a lower heating value of 12.57 MJ/Nm³ can be achieved by gasifying the SRF at 0.4 ER and 900 °C. However, compared to coal and biomass, the syngas efficiency of Korean SRF was less, which can be resolved by operating the gasification processes at high temperatures. If proper research and development activities are conducted on Korean SRF, it could be a good substitute for fossil fuels in the future.

Solid recovered fuel (SRF) residue, which is leftovers from the SRF manufacturing process, usually is discarded in landfill because of its low heating value and high ash and moisture content. However, it could be used as a fuel after mechanical and biological treatment. Gasification experiments were conducted on treated SRF residue (TSRFR) to assess the viability of syngas production. Efforts were also made to improve the gasification performance by adding low-cost natural minerals such as dolomite and lime as bed material, and by blending with biomass waste. In the case of additive mineral tests, dolomite showed better performance compared to lime, and in the case of biomass blends, a 25 wt% pine sawdust blend with TSRFR showed the best performance. Finally, as an appropriate condition, a combined experiment was conducted at an equivalence ratio (ER) of 0.2 using a 25 wt% pine sawdust blend with TSRFR as a feedstock and dolomite as the bed material. The highest dry gas yield (1.81 Nm³/kg), with the highest amount of syngas (56.72 vol%) and highest lower heating value (9.55 MJ/Nm³) was obtained in this condition. Furthermore, the highest cold gas efficiency (48.64%) and carbon conversion rate (98.87%), and the lowest residue yield (11.56%), tar (0.95 g/Nm³), and gas pollutants content was observed.

Proper treatment and careful management of sewage sludge are essential because its disposal can lead to adverse environmental impacts such as public health hazards, as well as air, soil, and water pollution. Several efforts are being made currently not only to safely dispose of sewage sludge but also to utilize it as an energy source. Therefore, in this study, initiatives were taken to valorize sewage sludge cake by reducing the moisture content and increasing the calorific value by applying a hydrothermal treatment technique for efficient energy recovery. The sludge cake treated at 200 °C for 1 h was found to be the optimum condition for hydrothermal carbonization, as, in this condition, the caloric value of the treated sludge increased by 10% and the moisture content removed was 20 wt.%. To recover energy from the hydrothermally treated sludge, a gasification technology was applied at 900 °C. The results showed that the product gas from hydrothermally treated sludge cake had a higher lower heating value (0.98 MJ/Nm³) and higher cold gas efficiency (5.8%). Furthermore, compared with raw sludge cake, less tar was generated during the gasification of hydrothermally treated sludge cake. The removal efficiency was 28.2%. Overall results depict that hydrothermally treated sewage sludge cake could be a good source of energy recovery via the gasification process.

In this study, we investigated the applicability of an automobile shredder residue (ASR) as an energy and recycling resource. First, ASR gasification was conducted in a fixed-bed reactor (throughput = 1 kg/h) at different temperatures (800, 1000, and 1200 °C) and an equivalence ratio of 0.1–0.5. Clay bricks were prepared with the solid residue obtained from the gasification process to address the issue of solid-residue production in pyrolysis. The syngas (H₂ + CO) from ASR gasification had maximum and minimum yields of approximately 86 and 40 vol.%, respectively. Furthermore, the yield of syngas increased with the temperature and equivalence ratio (ER); therefore, the optimum conditions for the ASR gasification were determined to be a temperature of 1200 °C and an ER of 0.5. In addition, solid residues, such as char and ash, began to melt due to thermal heating in the range of 1300–1400 °C and were converted into melting slag, which was subsequently used to manufacture clay bricks. The absorption ratios and compressive strengths of the clay bricks were compared to those set by Korean Industrial Standards to evaluate the quality of the clay bricks. As a result, the manufactured clay bricks were estimated to have a compressive strength of over 22.54 N/mm² and an absorption ratio of less than 10%. Additionally, greenhouse gas (GHG) emissions from the melting–gasification process were estimated and compared with those from ASR incineration, calculated using the greenhouse gas equations provided by the Korean Ministry of Environment. As a result, it was revealed that the GHG emissions from the combined melting–gasification process (gasification, melting system, and clay-brick manufacturing) were approximately ten times higher than those from the ASR-incineration process. Thus, in terms of operation cost on the carbon capture process for GHG reduction, the combined melting–gasification process would be a more efficient process than that of incineration.