A novel photocatalyst of Ta-doped ZnO nanoparticles was prepared by a modified Pechini-type method. The antimicrobial study of Ta-doped ZnO nanoparticles on several bacteria of Gram-positive Bacillus subtilis (B. subtilis) and Staphylococcus aureus (S. aureus) and Gram-negative Escherichia coli (E. coli) and Pseudomonas aeruginosa (P. aeruginosa) were performed using a standard microbial method. The Ta-doping concentration effect on the minimum inhibitory concentration (MIC) of various bacteria under dark ambient has been evaluated. The photocatalytical inactivation of Ta-doped ZnO nanoparticles under visible light irradiation was examined. The MIC results indicate that the incorporation of Ta5+ ions into ZnO significantly improve the bacteriostasis effect of ZnO nanoparticles on E. coli, S. aureus, and B. subtilis in the absence of light. Compared to MIC results without light irradiation, Ta-doped ZnO and pure ZnO nanoparticles show much stronger bactericidal efficacy on P. aeruginosa, E. coli, and S. aureus under visible light illumination. The possible antimicrobial mechanisms in Ta-doped ZnO systems under visible light and dark conditions were also proposed. Ta-doped ZnO nanoparticles exhibit more effective bactericidal efficacy than pure ZnO in dark ambient, which can be attributed to the synergistic effect of enhanced surface bioactivity and increased electrostatic force due to the incorporation of Ta5+ ions into ZnO. Based on the antibacterial tests, 5 % Ta-doped ZnO is a more effective antimicrobial agent than pure ZnO.
We have demonstrated a flexible resistive random access memory unit with trilayer structure by atomic layer deposition (ALD). The device unit is composed of Al2O3/HfO2/Al2O3-based functional stacks on TiN-coated Si substrate. The cross-sectional HRTEM image and XPS depth profile of Al2O3/HfO2/Al2O3 on TiN-coated Si confirm the existence of interfacial layers between trilayer structures of Al2O3/HfO2/Al2O3 after 600°C post-annealing. The memory units of Pt/Al2O3/HfO2/Al2O3/TiN/Si exhibit a typical bipolar, reliable, and reproducible resistive switching behavior, such as stable resistance ratio (>10) of OFF/ON states, sharp distribution of set and reset voltages, better switching endurance up to 103 cycles, and longer data retention at 85°C over 10 years. The possible switching mechanism of trilayer structure of Al2O3/HfO2/Al2O3 has been proposed. The trilayer structure device units of Al2O3/HfO2/Al2O3 on TiN-coated Si prepared by ALD may be a potential candidate for oxide-based resistive random access memory.
The HfO2/TiO2/HfO2 trilayer-structure resistive random access memory (RRAM) devices have been fabricated on Pt- and TiN-coated Si substrates with Pt top electrodes by atomic layer deposition (ALD). The effect of the bottom electrodes of Pt and TiN on the resistive switching properties of trilayer-structure units has been investigated. Both Pt/HfO2/TiO2/HfO2/Pt and Pt/HfO2/TiO2/HfO2/TiN exhibit typical bipolar resistive switching behavior. The dominant conduction mechanisms in low and high resistance states (LRS and HRS) of both memory cells are Ohmic behavior and space-charge-limited current, respectively. It is found that the bottom electrodes of Pt and TiN have great influence on the electroforming polarity preference, ratio of high and low resistance, and dispersion of the operating voltages of trilayer-structure memory cells. Compared to using symmetric Pt top/bottom electrodes, the RRAM cells using asymmetric Pt top/TiN bottom electrodes show smaller negative forming voltage of −3.7 V, relatively narrow distribution of the set/reset voltages and lower ratio of high and low resistances of 102. The electrode-dependent electroforming polarity can be interpreted by considering electrodes’ chemical activity with oxygen, the related reactions at anode, and the nonuniform distribution of oxygen vacancy concentration in trilayer-structure of HfO2/TiO2/HfO2 on Pt- and TiN-coated Si. Moreover, for Pt/HfO2/TiO2/HfO2/TiN devices, the TiN electrode as oxygen reservoir plays an important role in reducing forming voltage and improving uniformity of resistive switching parameters.
4 January 2020 in Journal of the Electrochemical Society
Hydrogen gas (H2) is used as an alternative renewable and eco-friendly energy source to replace the fossil fuel. However due to its explosive risks in air, the H2 production, storage and transportation are greatly limited. Hence, H2 sensor with quick response, highly sensitive and selective detection is of importance. Recently, zinc oxide (ZnO) as n-type semiconductor has attracted much attention in the field of H2 detection because of its easy synthesis, chemical/thermal stability and extremely abundant nanostructures. The recent advances in resistive-type H2 gas sensors based on ZnO nanostructures are reviewed in this paper. According to zero-dimension, one-dimension, and two-dimension, the H2 sensing properties and related mechanism of various kinds of pristine ZnO nanostructures-based sensors, such as nanowires, nanotubes, and nanofibers are summarized and compared. Furthermore, this paper focuses on strategies to improve the performance of H2 sensors (sensitivity, response speed, operation temperature, and limit of detection) by the surface modification, metal doping, formation of composite, and post-treatment of ZnO nanomaterials. Especially, the selectivity of ZnO nanosturctures-based H2 sensors to H2 in the presence of interfering gases is highlighted and the related enhancement approaches are discussed. Finally, the outlook and challenges on the ZnO nanostructures-based H2 sensors are addressed as well.
1 December 2018 in Progress in Natural Science: Materials International
Electrification has great impacts on our modern society. To electrify future transportation, state‐of‐the‐art lithium‐ion batteries (LIBs) are still not sufficient in multiple aspects including cost, energy density, lifespan, and safety. To this end, next‐generation high‐energy LIBs and beyond are highly regarded. In this regard, high‐capacity anodes are undergoing intensive investigation, such as silicon, SnO2, and lithium metal. However, such anode materials are commonly experiencing large volume changes and related issues, which are reflected on mechanical degradation, capacity fading, low efficiency, and unsatisfactory lifetime. To address these challenges, many technical strategies have been investigated. In the past decade, atomic layer deposition (ALD) has emerged as a new promising technique enabling atomic‐scale surface modification and nanoscale design of high‐capacity anodes for high performance. In this review, recent ALD studies on developing high‐capacity anodes for LIBs and beyond are thoroughly summarized. In addition, ALD strategies and their effectiveness in pursing high‐energy LIBs and beyond are discussed. Particularly, we highlighted the latest advances of ALD for addressing the notorious issues associated with Li metal anodes. It is expected that this work will promote the applications of ALD in new battery systems.