Reactivity control compression ignition engines illustrated suitable abilities in emission reduction beside high thermal efficiency. In this research, nine various direct fuel injection strategies were studied numerically: three cases with single injection strategy and six cases with split injection and different start of injection (SOI). In all simulated cases, equivalence ratio kept constant (i.e., 0.3). Among various strategies, single injection showed higher IMEP as a factor of efficiency with about 5.39 bar that occurred at SOI = 60 before top dead center (bTDC), while lower efficiency was observed for split injection case with 50%-50% injections of fuel in each injection stage. Start of combustion (SOC), burn duration and CA50 as factors for combustion characteristics were affected with SOI changes. In single SOI strategies, more advanced injection caused more advanced SOC where there was about 1.3 CAD advancing from 40 to 80 bTDC injection. Spilt SOI showed more advanced SOC, which, also more advanced, was allocated to 50%-50% split injection strategy. There was also the same trend in CA50 changes during change in SOI. Burn duration variations were insignificant and all of them approximately close to 4.5 CAD. According to the emissions researched in this study (Nitrogen Oxides (NOx), monoxide carbon (CO) and unburned hydro carbons (UHC)), all of these pollutants are below euro six diesel standards. Contours of emissions show that there were appropriate SOI for each case study, which were 45 degree bTDC for single strategy, 48 degree bTDC for 80%-20% mass injection and 70 degree bTDC for 50%-50% cases.
Hydrogen, as a suitable and clean energy carrier, has been long considered a primary fuel or in combination with other conventional fuels such as gasoline and diesel. Since the density of hydrogen is very low, in port fuel-injection configuration, the engine’s volumetric efficiency reduces due to the replacement of hydrogen by intake air. Therefore, hydrogen direct in-cylinder injection (injection after the intake valve closes) can be a suitable solution for hydrogen utilization in spark ignition (SI) engines. In this study, the effects of hydrogen direct injection with different hydrogen energy shares (HES) on the performance and emissions characteristics of a gasoline port-injection SI engine are investigated based on reactive computational fluid dynamics. Three different injection timings of hydrogen together with five different HES are applied at low and full load on a hydrogen–gasoline dual-fuel SI engine. The results show that retarded hydrogen injection timing increases the concentration of hydrogen near the spark plug, resulting in areas with higher average temperatures, which led to NOX emission deterioration at −120 Crank angle degree After Top Dead Center (CAD aTDC) start of injection (SOI) compared to the other modes. At −120 CAD aTDC SOI for 50% HES, the amount of NOX was 26% higher than −140 CAD aTDC SOI. In the meanwhile, an advanced hydrogen injection timing formed a homogeneous mixture of hydrogen, which decreased the HC and soot concentration, so that −140 CAD aTDC SOI implied the lowest amount of HC and soot. Moreover, with the increase in the amount of HES, the concentrations of CO, CO2 and soot were reduced. Having the HES by 50% at −140 CAD aTDC SOI, the concentrations of particulate matter (PM), CO and CO2 were reduced by 96.3%, 90% and 46%, respectively. However, due to more complete combustion and an elevated combustion average temperature, the amount of NOX emission increased drastically.
2 October 2024 in International Journal of Hydrogen Energy
Over the past few years, fuel prices have increased dramatically, and emissions regulations have become stricter in maritime applications. In order to take these factors into consideration, improvements in fuel consumption have become a mandatory factor and a main task of research and development departments in this area. Internal combustion engines (ICEs) can exploit only about 15–40% of chemical energy to produce work effectively, while most of the fuel energy is wasted through exhaust gases and coolant. Although there is a significant amount of wasted energy in thermal processes, the quality of that energy is low owing to its low temperature and provides limited potential for power generation consequently. Waste heat recovery (WHR) systems take advantage of the available waste heat for producing power by utilizing heat energy lost to the surroundings at no additional fuel costs. Among all available waste heat sources in the engine, exhaust gas is the most potent candidate for WHR due to its high level of exergy. Regarding WHR technologies, the well-known Rankine cycles are considered the most promising candidate for improving ICE thermal efficiency. This study is carried out for a six-cylinder marine diesel engine model operating with a WHR organic Rankine cycle (ORC) model that utilizes engine exhaust energy as input. Using expander inlet conditions in the ORC model, preliminary turbine design characteristics are calculated. For this mean-line model, a MATLAB code has been developed. In off-design expander analysis, performance maps are created for different speed and pressure ratios. Results are produced by integrating the polynomial correlations between all of these parameters into the ORC model. ORC efficiency varies in design and off-design conditions which are due to changes in expander input conditions and, consequently, net power output. In this study, ORC efficiency varies from a minimum of 6% to a maximum of 12.7%. ORC efficiency performance is also affected by certain variables such as the coolant flow rate, heat exchanger’s performance etc. It is calculated that with the increase of coolant flow rate, ORC efficiency increases due to the higher turbine work output that is made possible, and the condensing pressure decreases. It is calculated that ORC can improve engine Brake Specific Fuel Consumption (BSFC) from a minimum of 2.9% to a maximum of 5.1%, corresponding to different engine operating points. Thus, decreasing overall fuel consumption shows a positive effect on engine performance. It can also increase engine power output by up to 5.42% if so required for applications where this may be deemed necessary and where an appropriate mechanical connection is made between the engine shaft and the expander shaft. The ORC analysis uses a bespoke expander design methodology and couples it to an ORC design architecture method to provide an important methodology for high-efficiency marine diesel engine systems that can extend well beyond the marine sector and into the broader ORC WHR field and are applicable to many industries (as detailed in the Introduction section of this paper).
1 November 2005 in Combustion Science and Technology
Bioethanol has been successfully used in conventional spark ignition (SI) internal combustion engines. Homogeneous charge compression ignition (HCCI) combustion, a novel combustion method, has shown the potential for low nitric oxides (NOx) emissions with no particulate matter formation. This paper explores two different approaches to achieve HCCI with bioethanol; namely, trapping of internal residual gas and intake temperature heating with a high compression ratio. For naturally aspirated HCCI operation with residual gas trapping on a spark ignition engine, although the NOx emissions were low, the load range was unacceptably small. When inlet manifold pressurisation was employed, a substantial increase in the upper load boundary could be achieved without any substantial increase in NOx emissions. With forced induction, the feasibility of using boost control as the main method of load control for higher engine loads during HCCI operation has been explored with possible methods of utilizing boost control. One possible strategy is a map based strategy where fuelling rates are correlated versus boost pressure and trapped residual amounts. A proof of concept using this strategy showed that transient operation from a low load to a much higher load, using boost control might be possible without engine misfire.