Yali ZHANG

Yali ZHANG

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2013 in Applied Surface Science
Verified
Journal Article
Closed access
Liguo QinLiguo Qin
Liguo Qin
PLPing Lin
Ping Lin
YZYali ZHANG
Yali ZHANG
GDGuangneng Dong
Guangneng Dong
QZQunfeng Zeng
Qunfeng Zeng

10 January 2011 in Tribology Transactions
Verified
Journal Article
Closed access
YZYali ZHANG
Yali ZHANG
JMJunhong Mao
Junhong Mao
YXYou-Bai Xie
You-Bai Xie
In this article, an on-line visual ferrograph (OLVF) was used to monitor the wear condition of a vehicle engine during a bench test. A quantitative index of particle coverage area (IPCA) and wear debris ferro-image were obtained via OLVF to characterize wear degrees. On-line ferrograph analysis indicated some problems with the engine from about the 17th hour. A linear threshold value method to identify running condition of engines with the OLVF data was proposed. The OLVF data were in a fault zone after running for 25 h, when a base bolt broke and the engine stopped working during the test. The engine was disassembled and inspected after the test. Several wear scars were found on the cylinder walls as well as on the bearing surfaces. The oil was added at the 26th and 55th hours, which was also reflected by the variation of IPCA. Moreover, several off-line analyses were carried out in parallel. Off-line ferrograph data did not give any information about the abnormality and only showed stable wear debris content. Spectrometric oil analysis showed that there was no significant change in contents of metal elements.

1 December 2015 in Biosurface and Biotribology
Verified
Journal Article
Open access
YZYali ZHANG
Yali ZHANG
XZX.G. Zhang
X.G. Zhang
GMG. Matsoukas
G. Matsoukas
Ultra-high molecular weight polyethylene (UHMWPE) has been used in total joint arthroplasty for over 50 years. Conventionally, smooth UHMWPE surfaces are used for total joint replacements; however, smooth surface contacts have been shown to be inadequate in friction reduction and/or anti-wear. More recently, micro-textured surfaces have been investigated for reduction of the friction and wear of two contact interfaces. Unfortunately, the tribological behavior of textured UHMWPE surfaces requires further research to understand its tribological behavior. A numerical model is presented to understand the potential use of specially textured surfaces to improve the tribological properties of UHMWPE. A two dimensional, transient form of Reynolds equation was used to model the lubrication condition of the textured surfaces. The effects of area densities and pore depths over varying diameters were examined for several textured geometries including circle, rectangle, square and triangle. The simulation results show that the surface texturing can effectively be used to enhance hydrodynamic effects. More specifically, it was shown that the rectangular surface texture displayed superior characteristics over the other geometries investigated. The results provide a theoretical reference for the tribological design of surface texture on UHMWPE

1 November 2011 in Tribology International
Verified
Journal Article
Closed access
SPShiyuan Pei
Shiyuan Pei
SMShilei Ma
Shilei Ma
HXHua Xu
Hua Xu
FWFengcai Wang
Fengcai Wang
YZYali ZHANG
Yali ZHANG

14 March 2016 in Industrial Lubrication and Tribology
Verified
Journal Article
Closed access
YZYali ZHANG
Yali ZHANG
XZXiaogang Zhang
Xiaogang Zhang
TWTonghai Wu
Tonghai Wu
YXYou-Bai Xie
You-Bai Xie
Purpose: – The piston ring-cylinder liner pair is one of the most important tribological systems of an internal combustion engine. The friction loss of the piston ring-cylinder liner pair accounts for the largest portion of total efficiency losses. Therefore, improving the tribological system design of the piston ring-cylinder liner pair can reduce friction losses and bring tremendous economic benefits to society. This paper aims use surface texturing, which is proving to be an effective method, for improving the tribological performance of sliding surfaces. Design/methodology/approach: – In this paper, an experimental study using a pin-on-disk tribometer was carried out to evaluate the effects of surface texturing on friction reduction of piston rings under various loads and sliding velocities. Rectangular- and circular-shaped textures with different depths and area densities were produced by a Femtosecond laser. Comparison experiments were conducted with un-textured rings. Findings: – The results indicate that the friction performance of the ring surface was significantly improved by surface texturing, and the running-in stage was also shortened. More specifically, it was found that the rectangular-shaped texture had a better effect on friction reduction than the circular-shaped texture. Results also indicate that an optimum texture density existed for the rectangular-shaped texture. Additionally, it was observed that the average friction coefficient reduction of the textured ring decreased with increasing load and increased with increasing sliding velocity. Originality/value: – Consequently, these findings provide a more in-depth understanding of the relationship between micro-textures and tribological properties of piston rings in lubricating sliding.

25 April 2012 in Tribology Transactions
Verified
Journal Article
Closed access
TWTonghai Wu
Tonghai Wu
JWJunqun Wang
Junqun Wang
YPYeping Peng
Yeping Peng
YZYali ZHANG
Yali ZHANG
Analytical ferrography has been proved to be one of the most popular methods for wear characterization. However, it is limited by the real-time requirement of condition-based monitoring. A new wear characterization by on-line ferrograph images is proposed. The color of wear debris was studied based on an on-line visual ferrograph (OLVF) sensor. Generally, the features of on-line ferrograph images included low resolution, high contamination, and wear debris chains. The weak color of the wear debris, especially nonferrous metal debris, in an on-line ferrograph image was unavoidably merged into the mass noises. Accordingly, the on-line images were converted from the initial red, green, blue (RGB) format into hue, saturation, intensity (HSI) for the description of color images. The transmitted image was binarized to locate all wear debris and the wear debris was extracted by their pixels from the corresponding reflected image. The distributions of two HSI components, hue and intensity, were used to characterize the color of on-line ferrograph images. Aiming at the global noise induced by uneven light during sampling, the distributions of the hue and intensity of the wear debris were subtracted by that of the reflected image. As a result, the statistical colors of wear debris were extracted with the hue and intensity from the on-line ferrograph images. A designed experiment with manually prepared oil samples revealed that the wear debris of three common metals could be well differentiated according to their colors via the on-line ferrograph images. The method provides a primary exploration on describing the color of wear debris by on-line ferrograph images.