Invar alloys possess the peculiarity of dimensional invariance, which is of importance for high precision applications, such as measurement instruments. As ductile face-centered cubic (fcc) material, it is adequately weldable and is nowadays readily available as powder feed stock for additive manufacturing processes. Single-phase fcc alloys are known to often be highly textured, when fabricated via laser powder-bed fusion. Within this study, the thermal expansion behavior was analyzed via true differential dilatometry and the directional Young’s moduli were determined via impulse excitation technique in the temperature range up to 850 °C. The coefficient of thermal expansion was found to be nearly independent of the analyzed orientations. However, Young’s moduli differed by 20 GPa, with the highest stiffness obtained for specimens orientated parallel to the x-axis of the machines’ coordinate system.

Due to the production process, reinforcing steel bars possess an inhomogeneous microstructure associated with different material properties over the cross-section (e.g., hardness, ductility or strength). Furthermore, the surface required for the bond has a negative effect on the fatigue behavior. The first investigations were carried out in the 1970s and detected the fillet radius r as a key influencing factor. Until now, few studies had been carried out that investigate the quantification of the surface properties on the fatigue behavior, and none of them compared these properties with the local strengths of the material. The current paper presents the first results of a reverse-engineered reinforcing steel bar based on a previously performed laser scanning process. The rebar models were used to calculate the notch stress factors for different diameters based on von Mises stresses taken from FEM simulations. The notch stress factors showed a functional relationship with the fillet radius, which was already shown in the literature. Further experimental investigations on the fatigue and tensile behavior of the structural components in the investigated Tempcore^® rebars were carried out on microstructure specimens eroded by WEDM. The results of the tensile tests were used to derive a yield and tensile strength distribution in the cross-section. Depending on the microstructure, a yield strength between 415 N/mm² (ferrite/pearlite core) and 690 N/mm² (tempered martensite surface) was found. The acting notch stresses show a logarithmic dependency of the fillet radius, but do not reach the material strength of the surface.

Reinforcing steel bars (rebars) are widely manufactured using the Tempcore™ process. Several studies have been conducted analyzing the effect of the heat treatment route on the strength and corrosion resistance of rebars, but knowledge of its effects on the residual stresses of the finished product are largely lacking. This paper presents experimental investigations to identify the material parameters necessary to simulate the Tempcore™ process using thermo-elasto-plastic constitutive modeling in order to study the generation of residual stresses during the manufacturing process. Mechanical parameters such as yield strength at elevated temperatures and elastic constants were determined experimentally. A continuous cooling transformation diagram needed to model the phase transformations was also identified and is presented here. Residual stress distributions in the surface region of the rebar were characterized using X-ray diffraction. Further characterizations of microstructure, chemical composition, and hardness were carried out. The constitutive modeling approach for the numerical simulation is briefly described for which the experimentally determined parameters are required as input.

Ribbed reinforcing steel bars (rebars) are used for the reinforcement of concrete structures. In service, they are subjected to cyclic loading. Several studies addressing the relationship between rib geometry, stresses at the rebar surface induced by service loads and the rebar fatigue performance can be found in literature. However, the rebar’s fatigue performance is also influenced by residual stresses originating from the manufacturing process. In this contribution, a modeling approach is proposed to examine geometrically and thermo-mechanically induced stress concentrations in ribbed reinforcing bars made of the steel grade B500B. A linear-elastic load stress analysis and a thermo-mechanical analysis of the manufacturing process are conducted. The results are discussed and compared to literature results. In case of the load stress analysis, the results agree well with findings reported in literature and extend the current state of knowledge for B500B rebars with small diameters. In case of the thermo-mechanical analysis, compressive residual stresses at the rebar surface between two ribs and tensile residual stresses in the longitudinal direction at the tip of the ribs can be reported.