Thermal modification of wood has gained its niche in the production of materials that are mainly used for outdoor applications, where the stability of aesthetic appearances is very important. In the present research, spectral sensitivity to discoloration of thermally modified (TM) aspen wood was assessed and, based on these results, the possibility to delay discoloration due to weathering by non-film forming coating containing transparent iron oxides in the formulation was studied. The effect of including organic light stabilizers (UVA and HALS) in coatings as well as pretreatment with lignin stabilizer (HALS) was evaluated. Artificial and outdoor weathering was used for testing the efficiency of different coating formulations on TM wood discoloration. For color measurements and discoloration assessment, the CIELAB color model was used. Significant differences between the spectral sensitivity of unmodified and TM wood was observed by implying that different strategies could be effective for their photostabilization. From the studied concepts, the inclusion of the transparent red iron oxide into the base formulation of the non-film forming coating was found to be the most effective approach for enhancing TM wood photostability against discoloration due to weathering.
Effective prevention of mould growth indoors is still an important topic considering that mould growth is frequently observed in buildings, it causes serious health hazards and can irreversibly damage infected objects. Several studies have been conducted and mould growth models developed. Despite that, some potentially important aspects such as water damage and spore contamination have received only little attention. The objective of the present study was to investigate the effect of the initial moisture content of wood and spore contamination on mould development indoors. The mould tests were performed in constant temperature (10, 20 and 30 °C) and relative humidity (91% and 97%) conditions. The results show that wetting of wood specimens prior to the test significantly accelerates mould growth at a temperature of 10 °C. For the other temperatures, the effect was insignificant. Similar results were obtained for the test involving dry (conditioned at RH 50%) and conditioned specimens (RH 91% or RH 97%). The results regarding initial spore contamination show that significantly longer periods are required for mould to develop without spore contamination at 10 °C and 20 °C, while at 30 °C the effect is relatively small.
5 April 2023 in Construction and Building Materials
Considering interior applications, sunlight, both direct through open window and through window glass, and artificial lighting are the main sources of radiation possessing sufficient energy to trigger photodegradation processes in wood. LED lamps, which emit mostly visible light, are becoming the dominant artificial light source in various interiors. In the present study, photodegradation of thermally modified (TM) and unmodified (UM) ash (Fraxinus excelsior), aspen (Populus tremula), and pine (Pinus sylvestris) due to exposure to UV radiation and LED lamps was evaluated and compared by analysing wood discolouration (CIELAB colour space), changes in reflectance and FTIR spectra, and formation of water-soluble components. The results show that, apart from UV radiation, LED lamps may cause considerable photodegradation of both TM and UM wood resulting in visually perceptible colour change, alteration in chemical structure and formation of water-soluble components. Improved photo-stability was observed for TM wood exposed to UV radiation, while even more changes in FTIR spectra were detected for TM than UM wood in the experiment with LED lamps. Comparing TM and UM wood, the changes due to photodegradation were quite similar for TM wood of all species while significant differences were observed in the case of UM wood.
1 October 2016 in International Wood Products Journal
Thermally modified (TM) wood production has significantly increased in the last decade. The trend for TM wood residues should be similar – rapidly increasing, which has prompted this research on the possible efficient uses of these residues, such as sawdust. One of the possibilities could be the production of wood plastic composites (WPCs). In this work, three different hydrothermal modification regimes were used to modify birch boards. Modified and unmodified birch boards were milled to obtain sawdust. WPCs were made with a two-roll mill, and they consisted of 50 wt-% wood fibres + 50 wt-% polypropylene. Melt flow index (MFI), flexural properties, impact strength, microhardness water absorption and dimensional stability were tested. WPCs with TM wood showed improvement in flexural properties, MFI and other properties, however there was a decrease in impact strength. Scanning electron microscopy pictures of impact strength samples fracture surfaces were taken.
The aim of this research is to investigate and to evaluate the changes that occur on the surface of wood specimens, coated with three different coatings and exposed to artificial weathering. The three used coatings contain linseed oil and different types of pigments. Specimens of pine wood (Pinussylvestris L.) were painted with one or two layers of coatings to evaluate the discoloration and changes in lightness. For all the tested coatings, discoloration and loss of lightness were observed for all specimens regardless of the applied coatings. Different rates of color changes were observed for the tested coatings. The presence of pigments in the coatings formulation delays the discoloration of wood; as also the composition of pigments plays a significant role in the process.