This study investigates the relationship between clay minerals (kaolinite and illite) and rock properties of the claystone, including both mechanical (cohesion, friction angle, stress, and strain) and physical properties (natural water content, void ratio, and wet density), belonging to Warukin Formation of Kalimantan, Indonesia. Mineralogical characteristics of these rocks were studied using petrological and X-ray diffraction techniques, whereas the mechanical and physical properties were tested by conducting uniaxial and triaxial tests. Relationship among the variables was determined using correlation coefficients. It was observed that the mineralogy of the rocks pose strong constraints on their engineering properties. The results showed that an increase in illite content decreases cohesion, friction angle, strength, and safety factor; and increases natural moisture content, void ratio, and wet density. Although illite content of these rocks was just about 10.8% of the total minerals, it has significantly contributed to the modification of physical and mechanical properties. In contrast, kaolinite did not have a significant impact; since the correlation between various parameters was significantly low (correlation coefficient was much less, <0.3). Therefore while selecting the materials for geotechnical engineering applications, illite emerges as a safer alternative to kaolinite, especially when its concentration is less than 10.8% of the total rock mass.
Mapping the subsurface in slope stability analysis of disposal areas is difficult, especially the disposal layering materials that are assumed to be homogeneous instead of their real conditions. Moreover, the hoarding activities on high slope form layers based on the nature of the rock mechanics with large materials or boulders rolling down to the toe of the slope, while small ones are held at the top. Each layer formed, however, has certain geotechnical characteristics. The aim of this study is to determine the profiling of disposal material using a geoelectrical method known as Wenner–Schlumberger configuration with a line length of 450 m and also to find the resistivity value for mine waste materials based on an empirical number, which is a number that is obtained from the result reading compared to the actual condition in the field. The study was conducted on an in-pit dump with an estimated height of 150 m and a thickness of 50 m, and the data obtained were processed using RES2DINV software. The results showed that the subsurface cross-section has three layers consisting of bedrock with a resistivity of 50–70 Ωm, contact zone with 30–50 Ωm, and disposal material layer with 1–30 Ωm, which can be used for the slope stability analysis. This concept is very helpful for the geotechnical analysis on high mine waste dumps or sloping basement zone. This study focuses on the resistivity value for waste dump materials, which has not been clearly mentioned in the previous studies.
25 June 2022 in Bulletin of Engineering Geology and the Environment
The content of level has a big enough role in the value of the physical characteristic and the mechanical of material. The behavior of water in these materials needs to be analyzed first in order to support the slope stability analysis. Modeling of water behavior in materials in the construction of Tailing Storage Facilities (TSF) will be integrated in the slope stability analysis. This study aims to provide an explanation about the analysis of the Fishing Storage Facilities (TSF) which integrates transient groundwater analysis using the finite element method in supporting the stability analysis of the embankment of Tailing Storage Facilities (TSF). The variables that are used in the analysis, they are the parameters of physical properties and mechanic material for embankment and permeability parameters in analyzing groundwater. The analysis method for geotechnical and geohydrology modeling uses the finite element method. The results of analysis showed that groundwater behavior in the embankment material can be known in detail so that it can be integrated with stability analysis. It can be seen that there is a decrease in the value of the slope safety factor using the Integrated Slope Stability Analysis method compared to the conventional method. Adding an impermeable layer using a thickness of 5 m of clay material and a thickness of 20-30 m to support the retaining wall/foot is the criterion of optimal stability. The required lining material thickness (D) can be expressed by the following drawdown percentage equation function: reduction percentage = (1-0.8661D (-0.031)) * 100%.
21 January 2022 in Geomechanics and Geophysics for Geo-Energy and Geo-Resources