Over the last few years, microbubbles have found application in biomedicine. In this study, the characteristics of bubbles formed when air is introduced from a micro-tube (internal diameter 110 μm) in non-Newtonian shear thinning fluids are studied. The dependence of the release time and the size of the bubbles on the gas phase rate and liquid phase properties is investigated. The geometrical characteristics of the bubbles are also compared with those formed in Newtonian fluids with similar physical properties. It was found that the final diameter of the bubbles increases by increasing the gas flow rate and the liquid phase viscosity. It was observed that the bubbles formed in a non-Newtonian fluid have practically the same characteristics as those formed in a Newtonian fluid, whose viscosity equals the asymptotic viscosity of the non-Newtonian fluid, leading to the assumption that the shear rate around an under-formation bubble is high, and the viscosity tends to its asymptotic value. To verify this notion, bubble formation was simulated using Computational Fluid Dynamics (CFD). The simulation results revealed that around an under-formation bubble, the shear rate attains a value high enough to lead the viscosity of the non-Newtonian fluid to its asymptotic value.
We introduce Microgel-based Etalon Membranes (MEMs), based on the combination of stimuli-responsive microgels with an etalon, which is an optical device consisting of two reflecting plates and is used to filter specific wavelengths of light. The microgels are sandwiched between two reflective layers and, in response to a stimulus (e.g., temperature, pH, or biomarker concentration), swell or de-swell, thereby changing the distance between the two reflective layers and generating multiple peaks in the reflectance spectra. This property gives a MEM the unique capability of simultaneous separation and tunable responses to environmental changes and/or biomarker concentrations. We propose a design based on gold layers on a silicon nitride wafer membrane. Our comprehensive characterization, employing permeability experiments, in situ optical reflectance spectroscopy, in-liquid atomic force microscopy (AFM) analysis, and captive bubble contact angle measurements, elucidates the dynamic response of MEM to pH, temperature, and glucose stimuli and the corresponding effect of microgel swelling/de-swelling on the membrane properties, e.g., permeability. The AFM results confirm the dynamic changes of the microgel layer’s thickness on the membrane surface in response to the stimuli. Although the microgel’s swelling/de-swelling influences the effective pore radius, the decrease in the membrane’s permeance is limited to less than 10%. In the swollen state of the microgels, the etalon membranes show a prominent hydrophilic behavior, while they become less hydrophilic in the microgels’ de-swollen state. This work introduces MEM and provides novel insights into their behavior. The fundamental understanding that we reveal opens the way to applications ranging from point-of-care testing to continuous environmental monitoring.
Stimuli-responsive microgel-based etalons are promising optical and bio-sensors. These sensors play a pivotal role in modern healthcare by enabling rapid biomolecule detection, contributing to organ-on-chip applications and early disease diagnosis. This study investigates the suitability of poly(N-isopropylacrylamide) (pNIPAm)-based microgels for inkjet printing, focusing on optimizing their properties for effective deposition. Key parameters, including surface tension, viscosity, and particle size, are characterized to ensure compatibility with inkjet-printing requirements. The addition of surfactants tunes the suspensions’ properties to be in line with the requirements of inkjet printing. Jetting of pNIPAm-based microgels on gold-coated substrates forms a cohesive drop in a range of a few millimeters. Optical and scanning electron microscopy confirm the formation of a uniform microgel layer. The optical reflectance spectroscopy results indicate that inkjet-printed microgel-based etalons can effectively respond to changes in temperature and glucose concentration. In-liquid atomic force microscopy demonstrates the swelling dynamics of the microgels in different glucose concentrations, shedding light on their response dynamics. Our work demonstrates, for the first time, the feasibility of printing microgels in a controlled way, fabricating biocompatible inkjet-printed microgel-based etalon sensors with precise dimensions. The size precision and the sensitive monitoring capabilities of biomolecules hold great promise for in situ and continuous sensing in a wide range of biological and organ-on-chip applications.
Circulating tumor cell (CTC) clusters are major drivers of cancer metastasis, possessing higher metastatic potential than equal numbers of single CTCs. While their ability to traverse linear capillary segments has been studied, their transit behaviors in capillary bifurcations remain poorly understood. We utilized live-cell imaging and microfluidic devices that replicate the diverse geometries of human capillary bifurcations to investigate the transit dynamics of breast cancer clusters. We demonstrate that clusters dissociate into smaller clusters and single cells and that this phenomenon is strongly influenced by geometric features of equal and small-sized daughter channels in capillary bifurcations. Moreover, inhibition of actin polymerization increases both the frequencies of cluster dissociation and cell lysis during cluster transit in capillary bifurcations. Overall, our findings suggest that capillary biomechanics and actin filament polymerization affect the integrity of CTC clusters.