In recent years, man has become more aware of the fact that today’s approach to energy saving is unsustainable. It is believed that in the near future, biomass will increasingly become of interest as one of the most promising renewable energy sources. The paper describes one example of the use of biomass (corn cob) in the process of production of thermal energy, i.e. in the process of seedcorn drying. The purpose of the investigations reported in the paper was to define the use of corn cob as a fuel to increase energy efficiency. Additionally, energy efficiency was explained through hourly consumption of corn cob in thermogens, which was further compared with consumption of conventional fuels (natural gas).

Cement production is characterized by extremely high energy consumption per unit of product. Energy costs and environmental standards encouraged cement manufacturers worldwide to evaluate to what extent conventional fuels can be replaced by alternative fuels, i.e., processed waste materials, such as scrap tires. The decisive factors promoting the use of cement kilns for the utilization of scrap tires are: the high incineration temperature, the large area of the furnace, the significant length of the kiln, the long period of time the fuel stays inside the kiln, and the alkaline environment inside the kiln. The use of scrap tires in cement kilns is one of the best technologies for a complete and safe destruction of these wastes, due to the fact that there is a simultaneous benefit of destroying wastes and getting the energy. Thus, the use of scrap tires as alternative fuel in cement kilns has energy and economic justifiability, and it is environmentally friendly. In this article, monitoring results of nitrogen and sulfur oxides emissions from cement kilns in a cement factory in Serbia are given, depending on the ratio of scrap tires in total fuel quantity. Research was carried out for 0 to 15% share of scrap tires in total heat production. Nitrogen and sulfur oxides emission measurements from cement kilns were done during a trial use of scrap tires as a secondary fuel in a cement factory. During nitrogen and sulfur oxides emissions monitoring from the cement kiln, coal and petroleum coke were used as primary fuel, and whole or shredded tires were used as secondary fuel. Experimental results have shown the encouraging results: in particular, clinker characteristics were unmodified, and stack emissions of NOx and SO₂ were, in the case of tires, slightly decreased, in some cases were incremented, but remaining always below the law imposed limits.

In the petrochemical industry, an industrial pyrolysis furnace is a complicated piece of equipment that functions as both a reactor and high-pressure steam generator. During service, hard deposits of carbon (coke) build up on the inner wall of the tube, reducing heat transfer and restricting the flow of the hydrocarbon feedstocks. In this paper, an overview of coke formation, the impact of coke formation, and the methods by which coke formation can be prevented, as well as methods that can be successful in decoking of pyrolysis furnaces, is presented.

In the era of rapid technological growth, we are facing increased energy consumption. The question of using renewable energy sources is also essential for the sustainability of wireless sensor networks and the Industrial Internet of Things, especially in scenarios where there is a need to deploy an extensive number of sensor nodes and smart devices in industrial environments. Because of that, this paper targets the problem of monitoring the operations of solar-powered wireless sensor nodes applicable for a variety of Industrial IoT environments, considering their required locations in outdoor scenarios and the efficient solar power harvesting effects. This paper proposes a distributed wireless sensor network system architecture based on open-source hardware and open-source software technologies to achieve that. The proposed architecture is designed for acquiring solar radiation data and other ambient parameters (solar panel and ambient temperature, light intensity, etc.). These data are collected primarily to define estimation techniques using nonlinear regression for predicting solar panel voltage outputs that can be used to achieve energy-efficient operations of solar-powered sensor nodes in outdoor Industrial IoT systems. Additionally, data can be used to analyze and monitor the influence of multiple ambient data on the efficiency of solar panels and, thus, powering sensor nodes. The architecture proposal considers the variety of required data and the transmission and storage of harvested data for further processing. The proposed architecture is implemented in the small-scale variants for evaluation and testing. The platform is further evaluated with the prototype sensor node for collecting solar panel voltage generation data with open-source hardware and low-cost components for designing such data acquisition nodes. The sensor node is evaluated in different scenarios with solar and artificial light conditions for the feasibility of the proposed architecture and justification of its usage. As a result of this research, the platform and the method for implementing estimation techniques for sensor nodes in various sensor and IoT networks, which helps to achieve edge intelligence, is established.

This article presents the aspects of solar radiation and the use of solar energy in Serbia. It also considers why Serbia does not use thermal conversion of solar radiation in spite of much greater potential comparing to the countries of the Western and Central Europe, which are leading in the use of solar energy. The low standard of living, low electricity prices, the low level of energy efficiency in all areas of energy use, lack of knowledge, and political decisions are the main causes of insufficient use of renewable energy sources in Serbia.