The article describes the concept and analysis of virtualization technology and possible virtualization scenarios, which can be used to create a new generation of Intelligent Electronic Devices (IEDs). The overview of the concept was based on solutions used in conventional IT systems. A fully operational working lab environment, in which simulated IED models were implemented has been successfully tested. Problems associated with environment launch are described. An analysis of influence of virtual device time synchronization and resynchronization on their correct operations is performed. Time delays of communication when sending GOOSE messages between the IEDs using GOOSE packages are verified.

This paper describes the concept and analysis of virtualization technology and possible virtualization scenarios, which can be used to create a new generation of Intelligent Electronic Devices (IEDs). The concept overview was based on solutions used in conventional IT systems. A general conception of virtualization is presented. A solution based on KVM virtualization is described. Synchronizing the time of virtual machines, as well as creating and testing virtual machines under Linux operating systems are described. Time delays of communication when sending SV messages between the IEDs using SV packages are compared. Communication and operation of virtual protections with physical IEDs devices were verified.

Nonintrusive appliance load monitoring (NIALM) allows disaggregation of total electricity consumption into particular appliances in domestic or industrial environments. NIALM systems operation is based on processing of electrical signals acquired at one point of a monitored area. The main objective of this paper was to present the state-of-the-art in NIALM technologies for the smart home. This paper focuses on sensors and measurement methods. Different intelligent algorithms for processing signals have been presented. Identification accuracy for an actual set of appliances has been compared. This article depicts the architecture of a unique NIALM laboratory, presented in detail. Results of developed NIALM methods exploiting different measurement data are discussed and compared to known methods. New directions of NIALM research are proposed.

Series arc faults cause the majority of household fires involving electrical failures or malfunctions. Low-fault current amplitude is the reason for the difficulties faced in implementing effective arc detection systems. The paper presents a novel arc detection and faulty line identification method. It can be easily used in the low-voltage Alternate Current (AC) household network for arc detection in the Non-Intrusive Load Monitoring (NILM). Unlike existing methods, the proposed approach exploits both current and voltage signal time domain analysis. Experiments have been conducted with up to six devices operating simultaneously in the same circuit with an arc fault generator based on the IEC 62606:2013 standard. Sixteen time-domain features were used to maximize the arc-fault detection accuracy for particular appliances. Performance of the random forest classifier for arc fault detection was evaluated for 28 sets of features with five different sampling rates. For the single period analysis arc, detection accuracy was 98.38%, with F-score of 0.9870, while in terms of the IEC 62606:2013 standard, it was 99.07%, with F-score of 0.9925. Location of a series arc fault (line selection) was realized by identifying devices powered by the faulty line. The line selection was based on the Mean Values of Changes feature vector (MVC₅₀), calculated for absolute values of differences between adjacent current signal periods during the arc fault. The fault location accuracy was 93.20% for all cases and 98.20% for cases where the arc fault affected a single device.

The paper presents a novel method for non-intrusive appliances identification. It can be used for energy load disaggregation in a smart grid. The approach identifies changes in the state of the particular appliance by measuring and processing the common supply current signal. Analysis of the instantaneous changes in the aggregated current on the output of the analyzed circuit in the power network is exploited here. The signal is processed using the time alignment of the current and voltage signals samples represented in the array form. The scheme includes filtering, event detection and identification, which is performed by comparing parameters of the detected event against previously determined signatures of monitored appliances. The analysis is performed in the time domain; therefore (unlike other existing methods), the information contained in the original signal is not lost. The approach was tested in the laboratory designed specifically for this purpose. All tests have been conducted with up to 12 appliances operating at the same time in the single power supply circuit. The measurement setup was developed and used to record appliances’ switching on/off events. During tests, 2300 events for devices were recorded. Collected data were processed to identify particular devices with the accuracy of 98.8% and macro-averaged F-score measure of 0.9874. High identification accuracy was achieved despite the high number of devices operating in the background.