The paper presents a static lateral stability of a sub-compact tractor MT8-070 Mini in relation to a safe tractor operation. Axle weight distribution of the tractor was measured to calculate the vertical and longitudinal coordinates of a centre of gravity (COG). Experiments were aimed at the tractor equipped with no and four levels of rear wheel ballast weights (30.5, 61, 91.5 and 122 kg) at standard and extended overall width on tyres. A static overturning angle was calculated and experimentally measured when the tractor with right wheels touching the ground was in a state of unstable equilibrium. Comparing the experimental data with ISO 16231-2 (2015), the differences were 2.57%, 2.80%, 3.04%, 3.42% and 3.88% in the case of the standard overall width on tyres and 2.40%, 2.61%, 3.11%, 3.67% and 3.99% in the case of the extended overall width on tyres at 0, 30.5, 91.5 and 122 kg of the rear wheel ballast weight. Considering the vertical tyre deformation and the lateral shift of the tyre, the differences decreased to 0.95%, 1.11%, 1.29%, 1.85% and 1.42% (standard overall width on tyres) and 0.91%, 1.18%, 1.69%, 2.27% and 2.57% (extended overall width on tyres). The length of a rubber lug of a tyre contact patch did not change when the tractor was inclined at various ballast weights and did not affect the static overturning angle calculation according to ISO 16231-2 (2015). Results showed higher static overturning angle experimentally measured in comparison with calculated according to ISO 16231-2 (2015) due to the tyre deformation. Limiting the tractor operation on the basis of the static overturning angle calculated according to ISO 16231-2 (2015) avoids the tractor usage under dangerous operation conditions.

Worldwide, agricultural land is a dominant part of the environment. It is very important to understand the physical properties of soil because they directly or indirectly affect the entire human population. This paper proposes a data acquisition system for an original design of the soil resistance force sensor (SRFS). It serves to evaluate the properties of soil affected and unaffected by tractor passages through the field. The SRSF uses two cutting blades to measure soil mechanical resistance within the tire track and outside the tire track. The proposed system consists of two load cells, datalogger, power supply and software for personal computers. The system was practically tested under field operation. The results showed significant differences between the soil resistance force measured outside the tire track and within the tire track after one, two and three tractor passages. The data were compared with penetrometer resistance and soil bulk density, standardly characterizing soil mechanical resistance. An increase of soil resistance force after one, two and three tractor passages corresponded with an increase in reference parameters. The results showed that the proposed system is suitable for practical applications to evaluate soil mechanical resistance using SRFS.

Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, the scientific journal of the Mendel University in Brno, Czech Republic

This contribution presents the design and function verification of additional filtration. It is intended for the common transmission and hydraulic oil filling of tractors. The main role of this filtration concept is to ensure a high level of oil cleanness as a condition for the application of ecologic fluids in tractors. The next one is to decrease the wear of lubricated tractor components, the degradation of oil and eventually to extend the interval of oil change. The designed additional filtering is characterized by ease installation through the use of quick couplings and hoses to the external hydraulic circuit. Therefore, the filtration is suitable for various tractor types. Filter element has been designed with the filter ability 1micron and the ability to separate to 0.5 dm³ of water from oil. Function of additional filtration was verified during the 150 engine hours of tractor operation. During this time period the oil contamination was evaluated on the basis of chemical elements content such as Fe, Cu, Si, Al, Ni, Mo and Cr. The additive concentration was evaluated on the basis of chemical elements content such as Ca, P and Zn. During the test operation of tractor the concentration decrease of chemical elements reached the values 25.53 % (Fe), 23.53 % (Si), 25 % (Al) and 5.5 % (Cu). The decrease of additive concentration reached only medium level (6.6 %). Therefore, the designed additional filtration doesn’t remove additives from oil. Based on the evaluation of the content of chemical elements (that representing contamination and additives), we can say that the designed filtering method is suitable for use in agricultural tractors.

The paper presents the main drawbar parameters of tractor (drawbar pull, drawbar power and wheels slip) operating in a grass plot and evaluates the utilization of specially modified tyres with spikes. These prototypes of driving wheels were designed at the Department of Transport and Handling of the Slovak University of Agriculture in Nitra. The designed mechanism with spikes is mounted on standard tractor tyres, in which grooves were made. Spikes are hidden in grooves during transportation on a route. On the grassy landscape or soil, the spikes are ejected in order to improve the drawbar parameters. During operation, the drawbar pull and the rotation speeds of wheels were measured, whereupon the wheel slip was calculated. Results show the highest increase in tractor speed at the second gear and high load in utilized prototypes of the driving wheels (1.89 km·h ^-1 ) in comparison to standard tyres (1.10 km·h ^-1 ). Measurements also demonstrate the highest improvement of drawbar power under the aforementioned conditions in case of tractor with prototypes of driving wheels (1,719.87 W) in comparison with tractor using the standard tyres (1,061.57 W).

Driving wheel operation is characterized by force interactions with the ground, manifested in the form of vibrations. Signals generated by driving wheels can be analyzed in the frequency spectrum of tractor drawbar pull. The paper presents the analysis of a drawbar pull signal generated by a tractor equipped with two types of special driving wheels and standard tires. Beside the evaluation of special driving wheels’ properties according to drawbar power, the frequency spectra of measured signals were analyzed using a fast Fourier transformation. The model spectrum intervals for the standard tires, spike tires, and blade wheels were calculated according to the number of rubber lugs, blades, or spikes and compared with the experimental results. The results showed that the specific frequencies typical for blades and spikes were identified in model spectrum intervals. In the case of standard tires, the spectrum components typical for rubber lugs of the tire tread pattern were not identified. The highest amplitude of the typical frequency component was detected in the case of blades wheels, which showed the highest difference in drawbar power in comparison with the standard tires. Smaller dimensions of spikes resulted in lower amplitude and lower difference in drawbar power in comparison with the standard tires.