This study presents a new concept of controllable gas foil bearings (C-GFBs) with piezoelectric actuators. The C-GFB consists of a laminated top foil, bump foil, and piezo stacks and can simply change the bearing shape or film thickness locally and globally by varying the thickness of the piezo stacks with input voltages. The control schemes are (1) clearance control: the bearing clearance adjusted by changing overall piezo stack thickness, and (2) preload control: the mechanical preload modulated by the thickness expansion of several piezo stacks. Bearing lubrication performance is predicted for four cases of C-GFBs with different bearing clearances and preloads. The piezo stack control generates meaningful differences in the fluid-film thickness and pressure. Clearance control has a great effect on the dynamic force coefficients, but preload control slightly increases. Furthermore, the rotordynamic prediction of a rotor supported on two journal C-GFBs is conducted. As a result, both control modes for C-GFB are found to have a positive effect on rotordynamic amplitudes. Finally, using the orbit simulations, the C-GFB is controlled to have a small bearing clearance and large preload at critical speeds to make it possible to stably pass through the critical speeds. Consequently, it turns out that the C-GFB can improve bearing lubrication and rotordynamic performances by controlling only the input voltage of the piezo stacks. In addition, the C-GFB can be used to form various shapes to meet the operation conditions of an applied system.

This paper presents comprehensive test measurements for gas journal bearings with damping structures of a bump foil layer and/or a polymer layer. A one-pad top foil forms the bearing surface, under which the bearing structure and a bearing housing are located. Test bearings include gas foil bearings (GFBs), gas polymer bearings (GPBs), and gas foil-polymer bearings (GFPBs). In addition, three metal shims were employed to create wedge effects in the GFPBs. First, static load-deflection tests of test bearings estimate the radial assembly clearance. Second, shake dynamic loading tests identify frequency-dependent dynamic characteristics. An electromagnetic shaker provides flat bearing specimens with one degree-of-freedom (1DOF) vertical dynamic loading. GFPB was measured to exhibit a higher structural damping and lower stiffness than GFB. Lastly, the electric motor driving tests examine the rotordynamic stability performance. A permanent magnet (PM) synchronous motor drives a PM rotor supported on a pair of test journal bearings. As a result, the GFPBs with mechanical preloads enhanced the rotordynamic performance with no subsynchronous motions up to the maximum rotor speed of 88 krpm, and the bearing friction characteristics as well. Furthermore, they showed comparable rotordynamic performance to three-pad GFBs from a past literature, even with larger bearing clearances and small mechanical preloads.

The rotordynamic stability of journal gas foil–polymer bearings (GFPBs) applied to a dual-rotor bearing system was investigated. The GFPB has a high damping structure, i.e., it has an additional polymer layer, and top/bump/bottom foil structures. Test GFPBs were fabricated with nitrile butadiene rubber polymer layers with a thickness of 2 mm. Static-load-deflection tests of test gas foil bearings (GFBs) and GFPBs were performed to estimate the geometric bearing clearance (200 µm). The dual-rotor rotordynamic test rig consisted of a motor rotor, test rotor, and beam-type coupling. Two journal test bearings were installed on both the drive-end and non-drive-end sides of the test rotor. Predicting and testing the natural mode characteristics of the dual rotors revealed that the relative error between them was less than 7%, indicating that the first and second natural frequencies were 15 Hz and 160 Hz, respectively, and the third natural frequency was 1835 Hz in the tests. Based on the API 612 standard, the upper limit of the rotating speed for the test rig was limited to be approximately 92 krpm with a separation margin of 26%. Rotordynamic tests were conducted to examine the stability performance of GFBs and GFPBs, where the adjusted bearing clearance was 150 µm. The test results indicate that GFPBs have better stability performance in terms of delaying and suppressing unstable vibrations than GFBs. Specifically, GFPBs showed stable synchronous and subsynchronous responses up to a maximum rotating speed of 80 krpm. As a result, GFPB is a reliable lubricating element that can be used for vibration dampening in machines operating at relatively low temperatures.