This article presents a numerical optimization procedure of continuous gradient porous layer properties to achieve perfect absorption under normal incidence. This design tool is applied on a graded porous medium composed of a periodic arrangement of ordered unit cells allowing one to link the effective acoustic properties to its geometry. The best microgeometry continuous gradient providing the optimal acoustic reflection and/or transmission is designed via a nonlinear conjugate gradient algorithm. The acoustic performances of the so-designed continuous graded material are discussed with respect to the optimized homogeneous, i.e., nongraded and monotonically graded material. The numerical results show a shifting of the perfect absorption peak to lower frequencies or a widening of the perfect absorption frequency range for graded materials when compared to uniform ones. The results are validated experimentally on 3D-printed samples, therefore, confirming the relevance of such a gradient along with the efficiency of the control of the entire design process.
The purpose of this article is to experimentally study the damping of composite sandwich beams with lightweight honeycomb core. The top and bottom facesheets are made of carbon/epoxy layers with partial interleaved viscoelastic layers. A new damping approach consisting of selectively targeting the inflection points of the bending mode shapes is proposed. At the nodes, the shearing deformation in the beam is maximal, and so is the strain in the viscoelastic layers. The experimental investigation of damping is made by means of standard impact tests using an instrumented hammer performed on beam specimens. The nodes are determined experimentally by moving a small accelerometer along the beam axis and by measuring the amplitude of the acceleration at each point. This novel damping approach keeps the damping ratio as high as the ratio obtained with standard (full coverage) surface damping treatment while reducing the added mass by almost 50%. A comparison of the results obtained in this study with experimental and numerical results found in the literature leads to the conclusion that the most efficient way of damping this type of sandwich structure is to modify and/or improve the viscoelastic properties of the core.
16 December 2013 in Journal of Composite Materials
The main focus of this paper is the experimental comparative analysis of the viscoelastic properties of acrylic- and silicon-based viscoelastic materials. These materials are widely used in the aeronautic industry for structural and/or damping applications. It is therefore required to determine their viscoelastic properties such as shear modulus and loss factor following their integration to aircraft composite structures. The influence of material thickness, bonding quality, curing and cocuring with composite material was evaluated using dynamic mechanical analysis machine in plan shear configuration. This comparative analysis in the 0–600 Hz frequency range provides useful information that should be taken into consideration when designing bonded joints for structural and/or damping applications. The small variation of the acrylic-based material loss factor over a wide range of frequencies suggests that this material is a good candidate for damping applications at room temperature in metallic structures where no curing is required. However, cocuring of acrylic-based material with composite laminae increases its shear modulus up to six times with respect to the uncured material whereas its loss factor is reduced by about 20%. On the other hand, the silicon-based material remains stable after thermal treatment (curing and cocuring) suggesting that it is well suited for in situ damping treatment involving laminate composite structure. However, at room temperature its shear modulus after cocuring is lowered by almost 25% due to poor bonding quality, which depends on the nature of the substrate.
: It is generally known that piezoelectric material is inherently nonlinear. This nonlinearity is more apparent at high vibration amplitudes, which are generally present in a number of energy harvesting applications such as high-power machine tools, subway vehicles, aircraft engines and rotors. The effect of nonlinearity in piezoelectric energy harvesters (PEHs) implemented for these applications needs to be assessed and well understood. The purpose of this article is to model the material nonlinearities for a piezoelectric cantilever consisting of complex geometries. The geometries modeled in this work include morphological configurations (unimorph and bimorph), tapered beam profiles, partial piezoelectric layer coverage and tip mass. Within the existing literature, several geometry-specific nonlinear models are provided for the piezoelectric cantilever which makes the study of complex designs difficult. In this work, a generalized method is developed by incorporating the transfer matrix method. The nonlinear governing equations of the piezoelectric cantilever are generalized to include higher-order nonlinear terms until nth order. The governing equations are derived by utilizing the nonlinear piezoelectric constitutive equations in the extended Hamilton’s principle and a numerical Ordinary Differential Equation solver is used to obtain the PEH output. The nonlinear model is validated using finite element model, literature and experiments conducted on a bimorph PEH sample. It is found that nonlinear response of PEH is attributed to material nonlinearity and the contribution of higher-order nonlinear terms is significant.