We performed laboratory friction experiments on shale samples from three hydrocarbon reservoirs to assess compositional controls on fault slip behavior accompanying hydraulic stimulation. The samples span a range of clay and total organic content from ~10 to 60% by weight and demonstrate fine‐scale heterogeneity within each reservoir. Friction measurements demonstrate strong dependence of strength and rate‐state constitutive properties on shale composition. Shale samples with clay and organic content above ~30% by weight show coefficient of friction ~0.4 and consistently velocity‐strengthening behavior, while those below this threshold show increased strength and velocity‐weakening behavior. This transition in frictional strength and stability suggests a change in the shale grain packing framework from rigid clast supported to clay mineral and organic matter supported. Measurements of gouge dilatancy further support these relationships, showing a negative correlation with clay and organic content. Critical slip evolution distance exhibits similar dependence on composition, implying common micromechanical mechanisms for the observed transition in frictional behavior. We performed microstructural characterization of the experimental samples and observe changes in the gouge load‐bearing framework and shear localization features consistent with these mechanical data. While these results can be applied generally to infer slip stability on faults in clay‐bearing sedimentary rock, we employ the experimental data to place constraints on microearthquake magnitudes and the occurrence of slow shear slip on preexisting faults during hydraulic stimulation in shale reservoirs.
Oceanic transform faults represent abundant yet relatively unexplored components of the hydrologic cycle in the mantle lithosphere. Current models limit fluid circulation to 600 °C, the thermal limit of earthquakes recorded by teleseismic surveys. However, recent ocean‐bottom seismic surveys have located earthquakes at depths corresponding to >1000 °C in modeled thermal structure. To constrain the depth extent of brittle deformation and fluid infiltration, we analyzed peridotite mylonites dredged from the Shaka Transform Fault, Southwest Indian Ridge. Samples range from high strain mylonites that preserve ductile microstructures to lower strain mylonites that are fractured and overprinted by hydrothermal alteration. Microstructural analysis of the high strain samples reveals brittle deformation of pyroxene concomitant with ductile deformation of olivine and growth of amphibole. Porphyroclasts preserve healed fractures filled with fluid inclusions, implying repeated episodes of fracture, fluid infiltration, and healing. The association of hydration features with brittle structures points to seawater, rather than melt, as the fluid source. Textural analysis indicates that strain localization was initiated by grain boundary pinning and that olivine grain size was reduced to ~1 μm in the presence of amphibole. Comparing the amphibole stability field to thermometry estimates for the limit of recrystallization suggests that fluid flow extended to ~650–850 °C. Our results indicate that the hydrologic cycle extends past the brittle‐ductile transition and promotes strain localization via hydrolytic weakening and hydration reactions. We propose that seawater infiltration on oceanic transform faults is driven by the seismic cycle and represents a first order control on the rheology of the oceanic lithosphere.
We investigated the relationship between stratigraphy, stress, and microseismicity at the Hydraulic Fracture Test Site-1. The site comprises two sets of horizontal wells in the Wolfcamp shale and a deviated well drilled after hydraulic fracturing. Regional stresses indicate normal/strike-slip faulting with E-W compression. Stress measurements in vertical and horizontal wells show that the minimum principal stress varies with depth. Strata with high clay and organic content show high values of the least compressive stress, consistent with the theory of viscous stress relaxation. By integrating data from core, logs, and the hydraulic fracturing stages, we constructed a stress profile for the Wolfcamp sequence, which predicts how much pressure is required for hydraulic fracture growth. We applied the results to fracture orientation data from image logs to determine the population of pre-existing faults that are expected to slip during stimulation. We also determined microseismic focal plane mechanisms and found slip on steeply dipping planes striking NW, consistent with the orientations of potentially active faults predicted by the stress model. This case study represents a general approach for integrating stress measurements and rock properties to predict hydraulic fracture growth and the characteristics of injection-induced microseismicity.