Laser scanning via LiDAR is a powerful technique for collecting data necessary for Digital Terrain Model (DTM) generation, even in densely forested areas. LiDAR observations located at the ground level can be separated from the initial point cloud and used as input for the generation of a Digital Terrain Model (DTM) via interpolation. This paper proposes a quantitative analysis of the accuracy of DTMs (and derived slope maps) obtained from LiDAR data and is focused on conditions common to most forestry activities (rough, steep terrain with forest cover). Three interpolation algorithms were tested: Inverse Distance Weighted (IDW), Natural Neighbour (NN) and Thin-Plate Spline (TPS). Research was mainly focused on the issue of point data density. To analyze its impact on the quality of ground surface modelling, the density of the filtered data set was artificially lowered (from 0.89 to 0.09 points/m²) by randomly removing point observations in 10% increments. This provides a comprehensive method of evaluating the impact of LiDAR ground point density on DTM accuracy. While the reduction of point density leads to a less accurate DTM in all cases (as expected), the exact pattern varies by algorithm. The accuracy of the LiDAR-derived DTMs is relatively good even when LiDAR sampling density is reduced to 0.40–0.50 points/m² (50–60 % of the initial point density), as long as a suitable interpolation algorithm is used (as IDW proved to be less resilient to density reductions below approximately 0.60 points/m²). In the case of slope estimation, the pattern is relatively similar, except the difference in accuracy between IDW and the other two algorithms is even more pronounced than in the case of DTM accuracy. Based on this research, we conclude that LiDAR is an adequate method for collecting morphological data necessary for modelling the ground surface, even when the sampling density is significantly reduced.

A digital model of the ground surface has many potential applications in forestry. Nowadays, Light Detection and Ranging (LiDAR) is one of the main sources for collecting morphological data. Point clouds obtained via laser scanning are used for modelling the ground surface by interpolation, a process which is affected by various errors. Using LiDAR data to collect ground surface data for forestry applications is a challenging scenario because the presence of forest vegetation will hinder the ability of laser pulses to reach the ground. The density of ground observations will be therefore reduced and not homogenous (as it is affected by the variations in canopy density). Furthermore, forest areas are generally present in mountainous areas, in which case the interpolation of the ground surface is more challenging. In this paper, we present a comparative analysis of interpolation accuracy for nine algorithms, which are used for generating Digital Terrain Models from Airborne Laser Scanning (ALS) data, in mountainous terrain covered by dense forest vegetation. For most of the algorithms we find a similar performance in terms of general accuracy, with RMSE values between 0.11 and 0.28 m (when model resolution is set to 0.5 m). Five of the algorithms (Natural Neighbour, Delauney Triangulation, Multilevel B-Spline, Thin-Plate Spline and Thin-Plate Spline by TIN) have vertical errors of less than 0.20 m for over 90 percent of validation points. Meanwhile, for most algorithms, major vertical errors (of over 1 m) are associated with less than 0.05 percent of validation points. Digital Terrain Model (DTM) resolution, ground slope and point cloud density influence the quality of the ground surface model, while for canopy density we find a less significant link with the quality of the interpolated DTMs.

The Real-Time Kinematic (RTK) method is currently the most widely used method for positioning using Global Navigation Satellite Systems (GNSSs) due to its accuracy, efficiency and ease of use. In forestry, position is a critical factor for numerous applications, with GNSS currently being the preferred solution for obtaining such data. However, the decreased performance of GNSS observations in challenging environments, such as under the forest canopy, must be considered. This paper analyzes the performance of a survey-grade GNSS receiver under coniferous/deciduous tree cover. Unlike most previous research concerning this topic, the focus here is on employing a methodology that is as close as possible to real working conditions in the field of forestry. To achieve this, short observation times of 30 s were used, with corrections received directly in the field from a Continuously Operating Reference Station (CORS) of the national RTK network in Romania. In total, 84 test points were determined, randomly distributed under the canopy, with reference data collected by topographical surveys using total station equipment. In terms of the overall horizontal accuracy, an RMSE of 2.03 m and MAE of 1.63 m are found. Meanwhile, the overall vertical accuracy is lower, as expected, with an RMSE of 4.85 m and MAE of 4.01 m. The variation in GNSS performance under the different forest compositions was found to be statistically significant, while GNSS-specific factors such as DOP values only influenced the precision and not the accuracy of observations. We established that this methodology offers sufficient accuracy, which is application-dependent, even if the majority of GNSS solutions were code-based, rather than carrier-phase-based, due to strong interference from the vegetation.

Real-Time Kinematic (RTK) is currently the most widely used method for positioning using Global Navigation Satellite Systems (GNSS) due to its accuracy, efficiency and ease of use. In forestry, position is a critical factor for numerous applications, with GNSS nowadays the preferred solution for obtaining such data. However, the decreased performance of GNSS observations in challenging environments, such as under the forest canopy, must be considered. This paper analyzes the performance of a survey-grade GNSS receiver under coniferous/deciduous tree cover, with short observation times of 30 seconds and corrections received in the field from a Continuously Operating Reference Station (CORS) of the national RTK network in Romania. 84 test points were determined, randomly distributed under the canopy, with reference data collected by topographical surveys using total station equipment. Relatively good accuracies were obtained, especially for horizontal position (RMSEs of 1.47 – 2.07 meters). The variation of GNSS performance under the different forest compositions was found to be statistically significant, while GNSS-specific factors such as DOP values only influenced the precision and not the accuracy of observations. We established that this methodology offers sufficient accuracy, application-dependent, even if the majority of GNSS solutions were code-based, rather than carrier phase-based, due to strong interference from the vegetation.