We report in this paper an original analysis of microseismic events (MSEs) induced by an excavation operation in the clay environment of the Mont Terri underground rock laboratory. In order to identify the MSEs with confidence, we develop a restrictive but efficient multistep method for filtering the recorded events. We deduce the spatial distribution and processes associated with the excavation-induced damage from the spatial location and focal mechanisms of the MSEs. We observe an asymmetric geometry of the excavation damaged zone around the excavated gallery, without notable microseismic activity in the sandy facies sidewall, in contrast with the shaly facies sidewall where a first burst of events is recorded, followed by two smaller bursts: one locates ahead of the excavation front and is associated with a dominant double-couple component, suggesting bedding plane reworking, that is, shear fracture mode, and the MSEs of the other cluster inside the shaly sidewall of the gallery, with a dominant compensated linear vector dipole component, suggesting extensive cracking. We identify and discuss four major factors that seem to control the MSEs source mechanisms: lithology, geometry of the geological features, gallery orientation and direction of the main compressive stress.
Laboratory study of slope stability of granular media remains a challenge for modeling, understanding, and predicting natural hazards, such as avalanches and landslides, precursory signs of which are controlled by numerous physical parameters. The present work focuses on the impact of the humidity, in the range of , on the stability of monodisperse dense packings of spherical beads. The beads are in a transparent box that is slowly and continuously tilted and allows simultaneous top and lateral optical measurements of global displacements of grains at the surface, defined as precursors. Humidity increases the cohesion between the grains. By performing successive avalanches that destabilize deeper granular layers, we assess the role of the exposure time to the high humidity rates in the diffusion process to reach the hygroscopic equilibrium inside the packing. We highlight an increase of the stability and first precursor angles, associated to a constant angle increment between two consecutive precursors, with a dependency with both the diameter (, and 0.75 mm) and the material (glass and polystyrene) of the grains.
Multiscale seismic attributes based on the wavelet transform properties have been recently introduced and successfully applied to identify the geometry of a complex seismic reflector in an elastic medium. In the present paper, we extend this quantitative approach to anelastic media where intrinsic attenuation modifies the seismic attributes and thus requires a specific processing to retrieve them properly. The method assumes both an attenuation linearly dependent with the seismic wave frequency and a seismic source wavelet approximated with a Gaussian derivative function. We highlight a quasi-conservation of the Gaussian character of the wavelet during its propagation. We show that this shape can be accurately modeled by a Gaussian derivative function characterized by both a fractional integration and a frequency shift of the seismic source and we establish the relationship between these wavelet parameters and Q. Based on this seismic wavelet modeling, we design a time-varying shaping filter that enables to make constant the shape of the wavelet allowing to retrieve the wavelet transform properties. Introduced with a homogeneous step-like reflector, the method is first applied on a thin-bed reflector and then on a more realistic synthetic dataset based on an in situ acoustic impedance sequence and a high resolution seismic source. The results clearly highlight the efficiency of the method in restoring accurately the multiscale seismic attributes of complex seismic reflectors in anelastic media by the use of broadband seismic sources.
17 August 2021 in Journal of Geophysical Research: Solid Earth
Underground traffic activities spread ground‐borne vibrations in a complex way. The present work focuses on 173 individual vehicles tracked as moving sources of vibrations in the Mont Terri rock laboratory, located 95 m away from a motorway tunnel. Two neighboring geophones record the vertical ground velocity of traffic‐induced events with peak particle velocities ranging in 0.15–0.35 m/s. A dynamic cross‐correlation of the waveforms is used to align the individual events for coherent and robust analysis. A root mean square (rms) method allows identifying the main feature, centered at the Main Fault, and an unexpected feature located about 140 m apart. The dominant seismic frequencies are 15 and 10 Hz, respectively. The vehicle speeds (70–90 km/h), estimated from the time‐delay between the two features, and the seismic velocity (800–2,300 m/s), assessed from a simple kinematic model, are used to convert time to position along the tunnel, allowing modeling the local rms with the Bornitz's equation. The resolved frequency‐independent attenuation coefficients are 2.61 s/km in the Opalinus Clay including the gallery network, and 1.23 s/km in the Limestone, a contrast of elastic properties that defines a bimaterial interface. A particle motion analysis highlights body waves, with dominant vertically polarized shear waves above the Main Fault. The origin of the unexpected feature is discussed in terms of site effects and seismic propagation in a heterogeneous fracture network. Traffic‐induced events can be used as reproducible, low‐frequency, and non‐destructive sources with potential interest in long‐term monitoring at the scale of an underground gallery.
Quasi-periodic collective displacements of grains at the free surface of a tilted grain packing constitute precursors of granular avalanches. Laboratory experiments are commonly performed by slowly tilting the packing from 0° to the maximal stability angle θA. In these conditions, the number of precursors is too small to assess reproducible and robust statistical analyses of the precursor activity. To go beyond this limitation, we have developed a specific experimental protocol consisting of tilting the packing with successive oscillation cycles. We use a high-resolution optical camera and process the images of the packing free surface to identify precursory events during many consecutive cycles of a single packing. We observe the same behavior for all half-cycles, forth and back: appearance of the first precursors after the same variation of inclination, exponential evolution of the weak surface activity for the first precursors and linear growth of stronger surface activity for the following ones. The experimental protocol provides both reproducible precursor measurements based on large sample statistical inferences and a quasi-stationary state after one full-cycle. This approach is very promising for highlighting the effects of external parameters, including humidity and packing geometry.