Matthew Bryant

Prof. Matthew Bryant

orcid

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 January 2011 in Journal of Vibration and Acoustics
Verified
Journal Article
Closed access
PDF file
MBMatthew Bryant
Matthew Bryant
EGEphrahim Garcia
Ephrahim Garcia
This paper proposes a novel piezoelectric energy harvesting device driven by aeroelastic flutter vibrations of a simple pin connected flap and beam. The system is subject to a modal convergence flutter response above a critical wind speed and then oscillates in a limit cycle at higher wind speeds. A linearized analytical model of the device is derived to include the effects of the three-way coupling between the structural, unsteady aerodynamic, and electrical aspects of the system. A stability analysis of this model is presented to determine the frequency and wind speed at the onset of the flutter instability, which dictates the cut-in conditions for energy harvesting. In order to estimate the electrical output of the energy harvester, the amplitude and frequency of the flutter limit cycle are also investigated. The limit cycle behavior is simulated in the time domain with a semi-empirical nonlinear model that accounts for the effects of the dynamic stall over the flap at large deflections. Wind tunnel test results are presented to determine the empirical aerodynamic model coefficients and to characterize the power output and flutter frequency of the energy harvester as functions of incident wind speed.

11 September 2014 in Journal of Intelligent Material Systems and Structures
Verified
Journal Article
Closed access
MMMichael A Meller
Michael A Meller
MBMatthew Bryant
Matthew Bryant
EGEphrahim Garcia
Ephrahim Garcia
In spite of extensive modeling and characterization efforts, little is known about the energetics of McKibben muscle actuators. This article experimentally investigates the effectiveness of traditional McKibben muscles at converting fluid energy delivered to the actuator to mechanical output work over full actuation cycles. Once these efficiency metrics are established, a comparison of the efficiencies of traditional pneumatic fluidic artificial muscles and hydraulic fluidic artificial muscles is presented. Two new hydraulic oil compatible bladder materials are tested—an elastomeric Viton bladder and an inelastic low-density polyethylene bladder. The performance of these muscle variants is compared by measuring blocked force and free contraction as a function of pressure, hysteresis, and energy efficiencies. The measurement of fluid volume delivered to the fluidic artificial muscles over their actuation ranges is shown to be useful for evaluating the accuracy of existing cylindrical volume models. Models of the energy conversion efficiency are developed and compared to the experimental data. The results show that using an inelastic bladder significantly improves the efficiency, force capacity, and contraction range of McKibben muscles; however, it also increases the actuator’s hysteretic behavior. Powering the muscles hydraulically and operating at higher pressures improves the efficiency as well.

28 November 2011 in Smart Materials and Structures
Verified
Journal Article
Closed access
MBMatthew Bryant
Matthew Bryant
EWEric Wolff
Eric Wolff
EGEphrahim Garcia
Ephrahim Garcia

6 May 2012 in Journal of Intelligent Material Systems and Structures
Verified
Journal Article
Closed access
PDF file
MBMatthew Bryant
Matthew Bryant
RMRanjeev L Mahtani
Ranjeev L Mahtani
EGEphrahim Garcia
Ephrahim Garcia
This study experimentally demonstrates that a closely spaced array of aeroelastic flutter energy harvesters can exploit synergistic wake interactions to outperform the same number of harvesters operating in isolation. The fluttering motion of each energy harvester imparts an oscillating vortex wake into the flow downstream of the device. Wind tunnel experiments with arrays of two and four flutter energy harvesters show that this wake structure has significant effects on the vibration amplitude, frequency, and power output of the trailing devices. These wake interaction effects are shown to vary with the stream-wise and cross-stream separation distance between the harvesters. Over a defined range of separations, an advantageous frequency lock-in between the devices arises. When this occurs, the trailing harvesters can extract additional energy from the wake of upstream harvesters, causing larger oscillation amplitudes and higher power output in the trailing devices. Experiments to characterize this variation in power output due to these wake interaction effects and to determine the optimal spacing of the energy harvesters are presented and discussed. Smoke-wire flow visualization is used to examine the wake structure and investigate the mechanism of the array interactions.

19 March 2019 in IEEE Journal of Oceanic Engineering
Verified
Journal Article
Closed access
WSWilliam Stewart
William Stewart
WWWarren Weisler
Warren Weisler
MAMark Anderson
Mark Anderson
MBMatthew Bryant
Matthew Bryant
KPKara Peters
Kara Peters
In the design of hybrid unmanned aerial and underwater vehicles, buoyancy management and weight are two major factors. Large wing volumes used by unmanned air vehicles to fly efficiently drive vehicle buoyancy up, preventing them from submerging. Heavy active buoyancy control systems can overcome this, but cost weight, energy, and time to transition between underwater operation and flight. An alternative design, consisting of a passively flooding and draining wing, is presented in this paper. Relevant dynamic parameters for a full vehicle dynamic model are identified. A dynamic model of a draining structure is developed and verified experimentally on both a simple cylinder and a full wing structure. With proper tuning, the model captures the salient dynamic behavior of passive draining during vehicle egress. A prototype unmanned aerial and underwater vehicle was built, flown, and used to collect flight test data. The model is used to accurately predict the takeoff performance of the vehicle. As given, the model can be incorporated into a full vehicle dynamic model to aid in the design, simulation, and control of hybrid unmanned aerial and underwater vehicles with passively draining components.

25 July 2009
Verified
Conference Paper
Closed access
PDF file
MBMatthew Bryant
Matthew Bryant
EGEphrahim Garcia
Ephrahim Garcia
Energy harvesting has enabled new operational concepts in the growing field of wireless sensing. A novel energy harvesting device driven by aeroelastic flutter vibrations has been developed and could be used to complement existing environmental energy harvesters such as solar cells in wireless sensing applications. An analytical model of the mechanical, electromechanical, and aerodynamic systems suitable for designing aeroelastic energy harvesters for various flow applications are derived and presented. Wind tunnel testing was performed with a prototype energy harvester to characterize the power output and flutter frequency response of the device over its entire range of operating wind speeds. Finally, two wing geometries, a flat plate and a NACA 0012 airfoil were tested and compared.