Corrosion is considered a destructive phenomenon that affects almost all metals. Active infrared thermography is an online (no result delay) and non-intrusive (no process disruption) method of non-destructive testing (NDT), which has shown profound capabilities of detecting sub-surface metal loss. However, thermal reflections, non-uniform stimulation and lateral heat diffusion will remain as the most undesirable phenomena preventing the effective observation of sub-surface defects. This becomes more challenging when there is no a priori knowledge of the anomalies to effectively distinguish between defective and non-defective areas. In this work, cooling stimulation is considered as the thermal excitation mean as 1- a very few reports in this regard have been mentioned in the body of literature and 2- a dynamic setup was achieved that is found to be effective to minimise the possibility of disrupting reflections or artefacts registered by thermal camera similar to the case of using heating stimulation. A state-of-the-art prototype mechanism was manufactured. This equipment includes a carrier carrying a thermal camera and a cooling medium reservoir operating in reciprocating motion setup. This equipment is able to scan the test piece while cold stimulation is in operation, and immediately after that the camera registers the thermal evolution. An automated contrast enhancement pipeline using a variation of adaptive histogram equalisation (AHE) combined with principal component analysis (PCA) method was developed. The enhanced image results demonstrated the capability of accurately detecting sub-surface metal loss as low as 37.5% as well as an efficiently reconstructed reference (non-defective) area.
Detection and characterisation of hidden corrosion are considered challenging yet crucial activities in many sensitive industrial plants where preventing the loss of containment or structural reliability are paramount. In the last two decades, infrared (IR) thermography has proved to be a reliable means for inspection of corrosion or other sub-surface anomalies in low to mid thickness metallic mediums. The foundation of using IR thermography for defect detection and characterisation is based on active thermography. In this method of inspection, an external excitation source is deployed for the purpose of stimulating thermal evolutions inside objects. The presence of sub-surface defects disrupts the evolution of electromagnetic pulse inside an object. The reflection of altered pulse at the surface can be recorded through thermal camera in the form of temperature anomalies. Through authors’ previous works, cold thermography has shown that it can be a viable defect detection alternative to the most commonly used means of active thermography, known as heating. In the current work, the characterisation of defect dimensions, i.e., depth and diameter, has been explored. A simple analytical model for thermal contrast over defect is used in order to approximate the defect depth and diameter. This is achieved by comparing the similarities of the model and the experimental contrast time-series. A method of time-series similarity measurement known as dynamic time wrapping (DTW) is used to score the similarity between a pair of model and experiment time-series. The final outcome of the proposed experimental setup has revealed that there is a good potential to predict the metal loss of up to 50% in mid-thickness substrate even by deploying a less accurate nonradiometric thermal device and no advanced image processing.
Utilising cooling stimulation as a thermal excitation means has demonstrated profound capabilities of detecting sub-surface metal loss using thermography. Previously, a prototype mechanism was introduced which accommodates a thermal camera and cooling source and operates in a reciprocating motion scanning the test piece while cold stimulation is in operation. Immediately after that, the camera registers the thermal evolution. However, thermal reflections, non-uniform stimulation and lateral heat diffusions will remain as undesirable phenomena preventing the effective observation of sub-surface defects. This becomes more challenging when there is no prior knowledge of the non-defective area in order to effectively distinguish between defective and non-defective areas. In this work, the previously automated acquisition and processing pipeline is re-designed and optimised for two purposes: 1—Through the previous work, the mentioned pipeline was used to analyse a specific area of the test piece surface in order to reconstruct the reference area and identify defects. In order to expand the application of this device over the entire test area, regardless of its extension, the pipeline is improved in which the final surface image is reconstructed by taking into account multiple segments of the test surface. The previously introduced pre-processing method of Dynamic Reference Reconstruction (DRR) is enhanced by using a more rigorous thresholding procedure. Principal Component Analysis (PCA) is then used in order for feature (DRR images) reduction. 2—The results of PCA on multiple segment images of the test surface revealed different ranges of intensities across each segment image. This potentially could cause mistaken interpretation of the defective and non-defective areas. An automated segmentation method based on Gaussian Mixture Model (GMM) is used to assist the expert user in more effective detection of the defective areas when the non-defective areas are uniformly characterised as background. The final results of GMM have shown not only the capability of accurately detecting subsurface metal loss as low as 37.5% but also the successful detection of defects that were either unidentifiable or invisible in either the original thermal images or their PCA transformed results.