This paper reports the synthesis of pure and Cr-doped TiO2 nanoparticles with different doping concentrations by using a cost-effective solvothermal method. The as-synthesized nanoparticles were characterized by using X-ray diffraction, transmission electron microscopy and UVâVis spectroscopy to study their structural and optical properties. The XRD pattern showed the prepared material is pure anatase of the crystalline phase. Using TEM measurement, the average particles size is found to be about 11â13Â nm while selective area electron diffraction (SAED) patterns have confirmed the polycrystalline nature of the nanoparticles. The size of the crystallite is observed to be decreased with an increase in dopant (Cr) concentration. UVâVis absorption spectra showed enhanced absorption in the visible range in accordance with the doping concentration of Cr with a red shift in the absorption edge. The band gap energy of doped nanoparticles decreases in accordance with an increase in dopant concentration due to the reduced particles size. This presented work would be useful to tune the optical properties of doped and undoped metal oxide TiO2 for its optoelectronic applications. Keywords: X-ray diffraction, Crystallites, Polycrystalline, Anatase phase, Cr-doped TiO2 nanoparticle
Few works are reported on solvothermal preparation of nanoparticles by utilizing acetone alone without a surfactant. This synthesis approach is found to be prominent for producing the mesoporous structure, which is crucial in improving the dye loading of the photoanode. In addition, doping of metal ions is advantageous in order to bring down the excitation energy, which is promising for boosting the performance of the doped oxides. This research aims to synthesize various kinds of doped-TiO2 nanocrystals to serve as photoanode materials in dye-sensitized solar cells (DSSCs). An X-ray diffraction study evidenced the existence of the crystalline phase in pure and doped-TiO2 nanocrystals. Rietveld refinement study showed the mixed phases of crystalline TiO2 in the CrT, CuNT, and ST as compared to a single anatase phase in the samples PT, AgT, BT, CoT, FeT, SnT, ZT, VT, and ZMT. The absorption spectroscopy analysis demonstrated the reduced optical band gap from 3.10 to 2.79 eV. Scanning electron microscopy investigation endorsed the formation of TiO2 mesoporous microspheres with a mean diameter ranging from 200 to 331 nm along with a nanocrystal diameter ranging from 10 to 20 nm. Doping with the different dopants enhanced the conversion efficiency of DSSCs from 1.31 to ∼6%. Furthermore, we have performed the electrochemical impedance spectroscopy of DSSCs, and the findings are presented.
Silicon nitride is a versatile material since many decades due to its compatibility with conventional fabrication technology. Other than its potential applications in microelectronics, this material has been regarded as an antireflection coating in solar cells. In this paper, we present the fabrication and characterization of silicon nitride (Si3N4) films deposited at 750, 800 and 850°C using atmospheric chemical vapor deposition. We have investigated the effect of deposition temperature on the physical and optical properties of the prepared films. The refractive index and film thickness were found to be increased in accordance with an increase in the deposition temperature. Fourier transform infrared (FTIR) spectroscopy analysis showed the Si–N–Si stretching peak at 917cm−1 further, the full width at half maxima and Si–N–Si peak position showed their dependency on the deposition temperature. Finally, the optimal reflectance was observed through Si3N4 film deposited at temperature 800°C which confirms its suitability as an antireflection coating
Dielectric reflectors are the passive components that have their potential demands for various purposes, such as back-end reflector in solar cells, the band pass filters in optical instruments, thermal reflector and so on. Though well-established techniques for manufacturing such reflectors are available, the demand for their low-cost production with a minimum number of coatings has attracted the attention of the scientific community. In this framework, this paper addresses the process optimization for the low-cost and rapid fabrication of dielectric TiO2/SiO2 reflectors with 100% reflectance. Numerous studies are carried out to explore the structural, morphological, and optical characteristics of reflectors. We summarize that the desired reflection band of a selective-wavelength range can be realized by varying the precursor and catalyst concentrations, annealing cycle, and the spin rate. With this, we noticed the shifting of reflection window from the visible (Vis) to near-infrared (NIR) wavelength region using reflectors of merely 2.5 stacks of TiO2/SiO2 films. We also performed the thermal response of the reflector by radiating an infrared light source and observed an exceptional performance indicating its thermal shielding application.
1 February 2009 in Optical and Quantum Electronics